Network Working Group;;;;;P. Pan, Ed.
Request for Comments: 4090;Hammerhead Systems
Category: Standards Track;;;;;G. Swallow, Ed.
Cisco Systems
A. Atlas, Ed.
Avici Systems
May 2005

Fast Reroute Extensions to RSVP-TE for LSP Tunnels

Status of This Memo

This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements.; Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol.; Distribution of this memo is unlimited.

Copyright Notice

Copyright (C) The Internet Society (2005).

Abstract

This document defines RSVP-TE extensions to establish backup label-
switched path (LSP) tunnels for local repair of LSP tunnels.; These

mechanisms enable the re-direction of traffic onto backup LSP tunnels
in 10s of milliseconds, in the event of a failure.

Two methods are defined here.; The one-to-one backup method creates
detour LSPs for each protected LSP at each potential point of local
repair.; The facility backup method creates a bypass tunnel to
protect a potential failure point; by taking advantage of MPLS label
stacking, this bypass tunnel can protect a set of LSPs that have
similar backup constraints.; Both methods can be used to protect
links and nodes during network failure.; The described behavior and
extensions to RSVP allow nodes to implement either method or both and
to interoperate in a mixed network.

Table of Contents

1.; IntrodUCtion ...................................................3
1.1.; Background ...............................................4
2.; Terminology ....................................................4
3.; Local Repair Techniques ........................................6
3.1.; One-to-One Backup ........................................6
3.2.; Facility Backup ..........................................7
4.; RSVP Extensions ................................................8
4.1.; FAST_REROUTE Object ......................................8
4.2.; DETOUR Object ...........................................11
4.2.1. DETOUR Object for IPv4 Address ...................11
4.2.2. DETOUR Object for IPv6 Address ...................12
4.3.; SESSION_ATTRIBUTE Flags .................................13
4.4.; RRO IPv4/IPv6 Sub-object Flags ..........................14
5.; Head-End Behavior .............................................15
6.; Point of Local Repair (PLR) Behavior ..........................16
6.1.; Signaling a Backup Path .................................17
6.1.1. Backup Path Identification: Sender
Template-Specific ................................19

;;6.1.2. Backup Path Identification: Path-Specific ........19
6.2.; Procedures for Backup Path Computation ..................20
6.3.; Signaling Backups for One-to-One Protection .............21
6.3.1. Make-before-Break with Detour LSPs ...............22
6.3.2. Message Handling .................................23
6.3.3. Local Reroute of Traffic onto Detour LSP .........23
6.4. Signaling for Facility Protection .......................24
6.4.1. Discovering Downstream Labels ....................24
6.4.2. Procedures for the PLR before Local Repair .......24
6.4.3. Procedures for the PLR during Local Repair .......25
6.4.4. Processing Backup Tunnel"s ERO ...................26
6.5. PLR Procedures during Local Repair ......................26
6.5.1. Notification of Local Repair .....................26
6.5.2. Revertive Behavior ...............................27
7.; Merge Node Behavior ...........................................28
7.1.; Handling Backup Path Messages before Failure ............28
7.1.1. Merging Backup Paths using the Sender
Template-Specific Method .........................29
7.1.2. Merging Detours using the Path-Specific Method ...29
7.1.3. Message Handling for Merged Detours ..............31
7.2.; Handling Failures .......................................31
8.; Behavior of All LSRs ..........................................32
8.1.; Merging Detours in the Path-Specific Method .............32
9.; Security Considerations .......................................33
10. IANA Considerations ...........................................33

11. Contributors ..................................................35
12. Acknowledgments ...............................................36
13. Normative References ..........................................36

1.; Introduction

This document extends RSVP [RSVP] to establish backup label-switched
path (LSP) tunnels for the local repair of LSP tunnels.; This
extension will meet the needs of real-time applications such as voice
over IP, for which user traffic should be redirected onto backup LSP
tunnels in 10s of milliseconds.; This timing requirement can be
satisfied by computing and signaling backup LSP tunnels in advance of
failure and by re-directing traffic as close to the failure point as
possible.; In this way, the time for redirection includes no path
computation and no signaling delays, including delays to propagate
failure notification between label-switched routers (LSRs).; Speed of
repair is the primary advantage of the methods and extensions
described here.; The term local repair is used when referring to
techniques that re-direct traffic to a backup LSP tunnel in response
to a local failure.

A protected LSP is an eXPlicitly-routed LSP that is provided with
protection.; The repair methods described here are applicable only to
explicitly-routed LSPs.; Application of these methods to LSPs that
dynamically change their routes, such as LSPs used in unicast IGP
routing, is beyond the scope of this document.

Section 2 covers new terminology used in this document.; Section 3
describes two basic methods for creating backup LSPs.; Section 4
describes the RSVP protocol extensions to support local protection.
Section 5 presents the behavior of an LSR that seeks to request local
protection for an LSP.; The behavior of a potential point of local
repair (PLR) is given in Section 6, which describes how to determine
the appropriate strategy for protecting an LSP and how to implement
each of the strategies.; Section 7 describes the behavior of a merge
node, the LSR where a protected LSP and its backup LSP rejoin.
Finally, Section 8 discusses the required behavior of other nodes in
the network.

The methods discussed in this document depend upon three assumptions:

o;An LSR that is on the path of a protected LSP should always

assume that it is a merge point.; This is necessary because
the facility backup method does not signal backups through a
bypass tunnel before failure.

o;If the one-to-one backup method is used and a DETOUR object
is included, the LSRs in the traffic-engineered network
should support the DETOUR object.; This is necessary so that
the Path message containing the DETOUR object is not
rejected.

o;Understanding the DETOUR object is required to support the
path-specific method, which requires that LSRs in the
traffic-engineered network be capable of merging detours.

1.1.; Background

Several years before work began on this document, operational
networks had deployed two independent methods of doing fast reroute;
these methods are called here one-to-one backup and facility backup.
Vendors trying to support both methods experienced compatibility
problems in attempting to produce a single implementation capable of
interoperating with both methods.; There are technical tradeoffs
between the methods.; These tradeoffs are so topologically dependent
that the community has not converged on a single approach.

This document rationalizes the RSVP signaling for both methods so
that any implementation can recognize all fast reroute requests and
clearly respond.; The response may be positive if the method can be
performed, or it may be a clear error to inform the requester to seek
alternate backup means.; This document also allows a single
implementation to support both methods, thereby providing a range of
capabilities.; The described behavior and extensions to RSVP allow
LERs and LSRs to implement either method or both.

While the two methods could in principle be used in a single network,
it is expected that operators will continue to deploy either one or
the other.; The goal of this document is to standardize the RSVP
signaling so that a network composed of LSRs that implement both
methods or a network composed of some LSRs that support one method

and others that support both can properly signal among those LSRs to
achieve fast restoration.

2.; Terminology

The key Words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC2119 [RFC-WORDS].

The reader is assumed to be familiar with the terminology in [RSVP]
and [RSVP-TE].

LSR: Label-Switch Router.

LSP: An MPLS Label-Switched Path.; In this document, an LSP will
always be explicitly routed.

Local Repair: Techniques used to repair LSP tunnels quickly when a
node or link along the LSP"s path fails.

PLR: Point of Local Repair.; The head-end LSR of a backup tunnel
or a detour LSP.

One-to-One Backup: A local repair method in which a backup LSP is
separately created for each protected LSP at a PLR.

Facility Backup: A local repair method in which a bypass tunnel is
used to protect one or more protected LSPs that traverse the
PLR, the resource being protected, and the Merge Point in
that order.

Protected LSP: An LSP is said to be protected at a given hop if it
has one or multiple associated backup tunnels originating at
that hop.

Detour LSP: The LSP that is used to re-route traffic around a
failure in one-to-one backup.

Bypass Tunnel: An LSP that is used to protect a set of LSPs
passing over a common facility.

Backup Tunnel: The LSP that is used to backup up one of the many
LSPs in many-to-one backup.

NHOP Bypass Tunnel: Next-Hop Bypass Tunnel.; A backup tunnel that

;bypasses a single link of the protected LSP.

NNHOP Bypass Tunnel: Next-Next-Hop Bypass Tunnel.; A backup tunnel
that bypasses a single node of the protected LSP.

Backup Path: The LSP that is responsible for backing up one
protected LSP.; A backup path refers to either a detour LSP
or a backup tunnel.

MP: Merge Point.; The LSR where one or more backup tunnels rejoin
the path of the protected LSP downstream of the potential
failure.; The same LSR may be both an MP and a PLR
simultaneously.

DMP: Detour Merge Point.; In the case of one-to-one backup, this
is an LSR where multiple detours converge.; Only one detour
is signaled beyond that LSR.

Reroutable LSP: Any LSP for which the head-end LSR requests local
protection.; See Section 5 for more detail.

CSPF: Constraint-based Shortest Path First.

SRLG Disjoint: A path is considered to be SRLG disjoint from a
given link or node if the path does not use any links or
nodes which belong to the same SRLG as that given link or
node.

3.; Local Repair Techniques

Two different methods for local protection are described.; In the
one-to-one backup method, a PLR computes a separate backup LSP,
called a detour LSP, for each LSP that the PLR protects.; In the
facility backup method, the PLR creates a single bypass tunnel that
can be used to protect multiple LSPs.

3.1.; One-to-One Backup

In the one-to-one backup method, a label-switched path is established
that intersects the original LSP somewhere downstream of the point of
link or node failure.; A separate backup LSP is established for each
LSP that is backed up.

[R1]----[R2]----[R3]------[R4]------[R5]

; ;;;;;;;;;/;;/
[R6]----[R7]----[R8]------[R9]

Protected LSP:; [R1->R2->R3->R4->R5]
R1"s Backup:;[R1->R6->R7->R8->R3]
R2"s Backup:;[R2->R7->R8->R4]
R3"s Backup:;[R3->R8->R9->R5]
R4"s Backup:;[R4->R9->R5]

Example 1.; One-to-One Backup Technique

In the simple topology shown in Example 1, the protected LSP runs
from R1 to R5.; R2 can provide user traffic protection by creating a
partial backup LSP that merges with the protected LSP at R4.; We
refer to a partial one-to-one backup LSP [R2->R7->R8->R4] as a
detour.

To protect an LSP that traverses N nodes fully, there could be as
many as (N - 1) detours.; Example 1 shows the paths for the detours
necessary to protect fully the LSP in the example.; To minimize the
number of LSPs in the network, it is desirable to merge a detour back
to its protected LSP, when feasible.; When a detour LSP intersects
its protected LSP at an LSR with the same outgoing interface, it will
be merged.

When a failure occurs along the protected LSP, the PLR redirects
traffic onto the local detour.; For instance, if the link [R2->R3]
fails in Example 1, R2 will switch traffic received from R1 onto the
protected LSP along link [R2->R7], using the label received when R2
created the detour.; When R4 receives traffic with the label provided
for R2"s detour, R4 will switch that traffic onto link [R4-R5], using
the label received from R5 for the protected LSP.; At no point does
the depth of the label stack increase as a result of the detour.
While R2 is using its detour, traffic will take the path
[R1->R2->R7->R8->R4->R5].

3.2.; Facility Backup

The facility backup method takes advantage of the MPLS label stack.

Instead of creating a separate LSP for every backed-up LSP, a single
LSP is created that serves to back up a set of LSPs.; We call such an
LSP tunnel a bypass tunnel.

The bypass tunnel must intersect the path of the original LSP(s)
somewhere downstream of the PLR.; Naturally, this constrains the set
of LSPs being backed up via that bypass tunnel to those that pass
through some common downstream node.; All LSPs that pass through the
point of local repair and through this common node that do not also
use the facilities involved in the bypass tunnel are candidates for
this set of LSPs.

[R8]

[R1]---[R2]----[R3]-----[R4]---[R5]
/;
[R6]===[R7];;;[R9]

Protected LSP 1:[R1->R2->R3->R4->R5]
Protected LSP 2:[R8->R2->R3->R4]
Protected LSP 3:[R2->R3->R4->R9]
Bypass LSP Tunnel: [R2->R6->R7->R4]

Example 2.; Facility Backup Technique

In Example 2, R2 has built a bypass tunnel that protects against the
failure of link [R2->R3] and node [R3].; The doubled lines represent
this tunnel.; This technique provides a scalability improvement, in
that the same bypass tunnel can also be used to protect LSPs from any
of R1, R2, or R8 to any of R4, R5, or R9.; Example 2 describes three
different protected LSPs that are using the same bypass tunnel for
protection.

As with the one-to-one method, there could be as many as (N-1) bypass
tunnels to fully protect an LSP that traverses N nodes.; However,

each of those bypass tunnels could protect a set of LSPs.

When a failure occurs along a protected LSP, the PLR redirects
traffic into the appropriate bypass tunnel.; For instance, if link
[R2->R3] fails in Example 2, R2 will switch traffic received from R1
on the protected LSP onto link [R2->R6].; The label will be switched
for one which will be understood by R4 to indicate the protected LSP,
and the bypass tunnel"s label will then be pushed onto the label-
stack of the redirected packets.; If penultimate-hop-popping is used,
the merge point in Example 2, R4, will receive the redirected packet
with a label indicating the protected LSP that the packet is to
follow.; If penultimate-hop-popping is not used, R4 will pop the
bypass tunnel"s label and examine the label underneath to determine
the protected LSP that the packet is to follow.; When R2 is using the
bypass tunnel for protected LSP 1, the traffic takes the path
[R1->R2->R6->R7->R4->R5]; the bypass tunnel is the connection between
R2 and R4.

4.; RSVP Extensions

This specification defines two additional objects, FAST_REROUTE and
DETOUR, to extend RSVP-TE for fast-reroute signaling.; These new
objects are backward compatible with LSRs that do not recognize them
(see section 3.10 in [RSVP]).; Both objects can only be carried in
RSVP Path messages.

The SESSION_ATTRIBUTE and RECORD_ROUTE objects are also extended to
support bandwidth and node protection features.

4.1.; FAST_REROUTE Object

The FAST_REROUTE object is used to control the backup used for the
protected LSP.; This specifies the setup and hold priorities, session
attribute filters, and bandwidth to be used for protection.; It also
allows a specific local protection method to be requested.; This
object MUST only be inserted into the PATH message by the head-end
LER and MUST NOT be changed by downstream LSRs.; The FAST_REROUTE
object has the following format:

Class-Num = 205
C-Type = 1

0;;1;;2;;3
+-------------+-------------+-------------+-------------+
Length (bytes);;;;;Class-Num;;C-Type;

;;;+-------------+-------------+-------------+-------------+
Setup PrioHold Prio;Hop-limit;;;;Flags;
+-------------+-------------+-------------+-------------+
Bandwidth;
+-------------+-------------+-------------+-------------+
Include-any;
+-------------+-------------+-------------+-------------+
Exclude-any;
+-------------+-------------+-------------+-------------+
Include-all;
+-------------+-------------+-------------+-------------+

Setup Priority

The priority of the backup path with respect to taking
resources, in the range 0 to 7.; The value 0 is the highest
priority.; Setup Priority is used in deciding whether this
session can preempt another session.; See [RSVP-TE] for the
usage on priority.

Holding Priority

The priority of the backup path with respect to holding
resources, in the range 0 to 7.; The value 0 is the highest
priority.; Holding Priority is used in deciding whether this
session can be preempted by another session.; See [RSVP-TE] for

the usage on priority.

Hop-limit

The maximum number of extra hops the backup path is allowed to
take, from current node (a PLR) to an MP, with PLR and MP
excluded from the count.; For example, hop-limit of 0 means
that only direct links between PLR and MP can be considered.

Flags

0x01; One-to-One Backup Desired

Requests protection via the one-to-one backup method.

0x02; Facility Backup Desired

Requests protection via the facility backup method.

Bandwidth

Bandwidth estimate; 32-bit IEEE floating point integer, in
bytes per second.

Exclude-any

A 32-bit vector representing a set of attribute filters
associated with a backup path, any of which renders a link
unacceptable.

Include-any

A 32-bit vector representing a set of attribute filters
associated with a backup path, any of which renders a link
acceptable (with respect to this test).; A null set (all bits
set to zero) automatically passes.

Include-all

A 32-bit vector representing a set of attribute filters
associated with a backup path, all of which must be present for
a link to be acceptable (with respect to this test).; A null
set (all bits set to zero) automatically passes.

The two high-order bits of the Class-Num (11) cause nodes that do not
understand the object to ignore it and pass it forward unchanged.

For informational purposes, a different C-Type value and format for
the FAST_REROUTE object are specified below.; This is used by legacy
implementations.; The meaning of the fields is the same as that

described for C-Type 1.

Class-Num = 205
C-Type = 7

0;;1;;2;;3
+-------------+-------------+-------------+-------------+
Length (bytes);;;;;Class-Num;;C-Type;
+-------------+-------------+-------------+-------------+
Setup PrioHold Prio;Hop-limit;Reserved;
+-------------+-------------+-------------+-------------+
Bandwidth;
+-------------+-------------+-------------+-------------+
Include-any;
+-------------+-------------+-------------+-------------+
Exclude-any;
+-------------+-------------+-------------+-------------+

Unknown C-Types should be treated as specified in [RSVP] Section
3.10.

4.2.; DETOUR Object

The DETOUR object is used in the one-to-one backup method to identify
detour LSPs.

4.2.1.; DETOUR Object for IPv4 Address

Class-Num = 63
C-Type = 7

0;;1;;;2;;3
+-------------+-------------+-------------+-------------+

;;;Length (bytes);;;;;Class-Num;;C-Type;
+-------------+-------------+-------------+-------------+
PLR_ID; 1;;;;;
+-------------+-------------+-------------+-------------+
Avoid_Node_ID 1;
+-------------+-------------+-------------+-------------+
//;;;;;....; //
+-------------+-------------+-------------+-------------+
PLR_ID; n;;;;;
+-------------+-------------+-------------+-------------+
Avoid_Node_ID; n
+-------------+-------------+-------------+-------------+

PLR_ID; (1 - n)

IPv4 address identifying the PLR that is the beginning point of
the detour.; Any local address on the PLR can be used.

Avoid_Node_ID; (1 - n)

IPv4 address identifying the immediate downstream node that the
PLR is trying to avoid.; Any local address of the downstream
node can be used.; This field is mandatory and is used by the

MP for the merging rules discussed below.

4.2.2.; DETOUR Object for IPv6 Address

Class-Num = 63
C-Type = 8

0;;1;;;2;;3
+-------------+-------------+-------------+-------------+
Length (bytes);;;;;Class-Num;;C-Type;
+-------------+-------------+-------------+-------------+
PLR_ID; 1;;;;;
+-------------+-------------+-------------+-------------+
PLR_ID; 1 (continued);
+-------------+-------------+-------------+-------------+
PLR_ID; 1 (continued);
+-------------+-------------+-------------+-------------+
PLR_ID; 1 (continued);
+-------------+-------------+-------------+-------------+
Avoid_Node_ID 1;
+-------------+-------------+-------------+-------------+
Avoid_Node_ID 1 (continued);;;;;

;;;;;+-------------+-------------+-------------+-------------+
Avoid_Node_ID 1 (continued);;;;;
+-------------+-------------+-------------+-------------+
Avoid_Node_ID 1 (continued);;;;;
+-------------+-------------+-------------+-------------+
//;;;;;....; //
+-------------+-------------+-------------+-------------+

PLR_ID; (1 - n)

An IPv6 128-bit unicast host address identifying the PLR that
is the beginning point of the detour.; Any local address on the
PLR can be used.

Avoid_Node_ID; (1 - n)

An IPv6 128-bit unicast host address identifying the immediate
downstream node that the PLR is trying to avoid.; Any local
address on the downstream node can be used.; This field is
mandatory and is used by the MP for the merging rules discussed
below.

There can be more than one pair of (PLR_ID, Avoid_Node_ID) entries in
a DETOUR object.; If detour merging is desired, after each merging
operation, the Detour Merge Point should combine all the merged
detours in subsequent Path messages.

The high-order bit of the Class-Num is zero; LSRs that do not support
the DETOUR objects MUST reject any Path message containing a DETOUR
object and send a PathErr to notify the PLR.; This PathErr SHOULD be
generated as specified in [RSVP] for unknown objects with a Class-Num
of the form "0bbbbbbb".

Unknown C-Types should be treated as specified in [RSVP] Section
3.10.

4.3.; SESSION_ATTRIBUTE Flags

To request bandwidth and node protection explicitly, two new flags

are defined in the SESSION_ATTRIBUTE object.

For both C-Type 1 and 7, the SESSION_ATTRIBUTE object currently has
the following flags defined [RSVP-TE]:

Local protection desired:0x01

This flag permits transit routers to use a local repair
mechanism that may result in violation of the explicit route
object.; When a fault is detected on an adjacent downstream
link or node, a transit node may reroute traffic for fast
service restoration.

Label recording desired:0x02

This flag indicates that label information should be included
when doing a route record.

SE Style desired:0x04

This flag indicates that the tunnel ingress node may choose to
reroute this tunnel without tearing it down.; A tunnel egress
node SHOULD use the SE Style when responding with a Resv
message.; When requesting fast reroute, the head-end LSR SHOULD
set this flag; this is not necessary for the path-specific
method of the one-to-one backup method.

The following new flags are defined:

Bandwidth protection desired:; 0x08

This flag indicates to the PLRs along the protected LSP path
that a backup path with a bandwidth guarantee is desired.; The
bandwidth to be guaranteed is that of the protected LSP, if no
FAST_REROUTE object is included in the PATH message; if a
FAST_REROUTE object is in the PATH message, then the bandwidth
specified therein is to be guaranteed.

Node protection desired: 0x10

This flag indicates to the PLRs along a protected LSP path that
a backup path that bypasses at least the next node of the
protected LSP is desired.

4.4.; RRO IPv4/IPv6 Sub-object Flags

To report whether bandwidth and/or node protection are provided as

requested, we define two new flags in the RRO IPv4 sub-object.

The RRO IPv4 and IPv6 address sub-objects currently have the
following flags defined [RSVP-TE]:

Local protection available:; 0x01

Indicates that the link downstream of this node is protected
via a local repair mechanism, which can be either one-to-one or
facility backup.

Local protection in use:; 0x02

Indicates that a local repair mechanism is in use to maintain
this tunnel (usually in the face of an outage of the link it
was previously routed over, or an outage of the neighboring
node).

Two new flags are defined:

Bandwidth protection:; 0x04

The PLR will set this bit when the protected LSP has a backup
path that is guaranteed to provide the desired bandwidth that
is specified in the FAST_REROUTE object or the bandwidth of the
protected LSP, if no FAST_REROUTE object was included.; The PLR
may set this whenever the desired bandwidth is guaranteed; the
PLR MUST set this flag when the desired bandwidth is guaranteed
and the "bandwidth protection desired" flag was set in the
SESSION_ATTRIBUTE object.; If the requested bandwidth is not
guaranteed, the PLR MUST NOT set this flag.

Node protection:; 0x08

The PLR will set this bit when the protected LSP has a backup
path that provides protection against a failure of the next LSR
along the protected LSP.; The PLR may set this whenever node
protection is provided by the protected LSP"s backup path; the
PLR MUST set this flag when the node protection is provided and
the "node protection desired" flag was set in the
SESSION_ATTRIBUTE object.; If node protection is not provided,

the PLR MUST NOT set this flag.; Thus, if a PLR could only set
up a link-protection backup path, the "Local protection
available" bit will be set, but the "Node protection" bit will
be cleared.

5.; Head-End Behavior

The head-end of an LSP determines whether local protection should be
requested for that LSP and which local protection method is desired
for the protected LSP.; The head-end also determines what constraints
should be requested for the backup paths of a protected LSP.

To indicate that an LSP should be locally protected, the head-end LSR
MUST either set the "local protection desired" flag in the
SESSION_ATTRIBUTE object or include a FAST_REROUTE object in the PATH
message, or both.; The "local protection desired" flag in the
SESSION_ATTRIBUTE object SHOULD always be set.; If a head-end LSR
signals a FAST_REROUTE object, it MUST be stored for Path refreshes.

The head-end LSR of a protected LSP MUST set the "label recording
desired" flag in the SESSION_ATTRIBUTE object.; This facilitates the
use of the facility backup method.; If node protection is desired,
the head-end LSR should set the "node protection desired" flag in the
SESSION_ATTRIBUTE object; otherwise, this flag should be cleared.
Similarly, if a guarantee of bandwidth protection is desired, then
the "bandwidth protection desired" flag in the SESSION_ATTRIBUTE
object should be set; otherwise, this flag should be cleared.; If the
head-end LSR determines that control of the backup paths for the
protected LSP is desired, then the LSR should include the
FAST_REROUTE object.; The PLRs will use the attribute filters,
bandwidth, hop-limit, and priorities to determine the backup paths.

If the head-end LSR desires that the one-to-one backup method be used
for the protected LSP, then the head-end LSR should include a
FAST_REROUTE object and set the "one-to-one backup desired" flag.; If
the head-end LSR desires that the protected LSP be protected via the
facility backup method, then the head-end LSR should include a
FAST_REROUTE object and set the "facility backup desired" flag.; The
lack of a FAST_REROUTE object, or having both these flags clear,
should be treated by PLRs as a lack of preference.; If both flags are
set, a PLR may use either method or both.

The head-end LSR of a protected LSP MUST support the additional flags

defined in Section 4.4 being set or clear in the RRO IPv4 and IPv6
sub-objects.; The head-end LSR of a protected LSP MUST support the
RRO Label sub-object.

If the head-end LSR of an LSP determines that local protection is
newly desired, this SHOULD be signaled via make-before-break.

6.; Point of Local Repair (PLR) Behavior

Every LSR along a protected LSP (except the egress) MUST follow the
PLR behavior described in this document.

A PLR SHOULD support the FAST_REROUTE object, the "local protection
desired", "label recording desired", "node protection desired", and
"bandwidth protection desired" flags in the SESSION_ATTRIBUTE object,
and the "local protection available", "local protection in use",
"bandwidth protection", and "node protection" flags in the RRO IPv4
and IPv6 sub-objects.; A PLR MAY support the DETOUR object.

A PLR MUST consider an LSP to have asked for local protection if the
"local protection desired" flag is set in the SESSION_ATTRIBUTE
object and/or the FAST_REROUTE object is included.; If the
FAST_REROUTE object is included, a PLR SHOULD consider providing
one-to-one protection if the "one-to-one desired" is set, and it
SHOULD consider providing facility backup if the "facility backup
desired" flag is set.; If the "node protection desired" flag is set,
the PLR SHOULD try to provide node protection; if this is not
feasible, the PLR SHOULD then try to provide link protection.; If the
"bandwidth protection guaranteed" flag is set, the PLR SHOULD try to
provide a bandwidth guarantee; if this is not feasible, the PLR
SHOULD then try to provide a backup without a guarantee of the full
bandwidth.

The following treatment for the RRO IPv4 or IPv6 sub-object"s flags
must be followed if an RRO is included in the protected LSP"s RESV
message.; Based on this additional information, the head-end may take
appropriate actions.

- Until a PLR has a backup path available, the PLR MUST clear the
relevant four flags in the corresponding RRO IPv4 or IPv6 sub-
object.

- Whenever the PLR has a backup path available, the PLR MUST set the
"local protection available" flag.; If no established one-to-one
backup LSP or bypass tunnel exists, or if the one-to-one LSP and
the bypass tunnel is in "DOWN" state, the PLR MUST clear the

;;;"local protection available" flag in its IPv4 (or IPv6) address
sub-object of the RRO and SHOULD send the updated RESV.

- The PLR MUST clear the "local protection in use" flag unless it is
actively redirecting traffic into the backup path instead of along
the protected LSP.

- The PLR SHOULD also set the "node protection" flag if the backup
path protects against the failure of the immediate downstream
node, and, if the path does not, the PLR SHOULD clear the "node
protection" flag.; This MUST be done if the "node protection
desired" flag was set in the SESSION_ATTRIBUTE object.

- The PLR SHOULD set the "bandwidth protection" flag if the backup
path offers a bandwidth guarantee, and, if the path does not, the
PLR SHOULD clear the "bandwidth protection" flag.; This MUST be
done if the "bandwidth protection desired" flag was set in the
SESSION_ATTRIBUTE object.

6.1.; Signaling a Backup Path

A number of objectives must be met to oBTain a satisfactory signaling
solution.; These are summarized as follows:

1. Unambiguously and uniquely identifying backup paths.

2. Unambiguously associating protected LSPs with their backup
paths.

3. Working with both global and non-global label spaces.

4. Allowing merging of backup paths.

5. Maintaining RSVP state during and after fail-over.

LSP tunnels are identified by a combination of the SESSION and
SENDER_TEMPLATE objects [RSVP-TE].; The relevant fields are as
follows.

IPv4 (or IPv6) tunnel end point address

IPv4 (or IPv6) address of the egress node for the tunnel.

Tunnel ID

A 16-bit identifier used in the SESSION that remains constant
over the life of the tunnel.

Extended Tunnel ID

A 32-bit (IPv4) or 128-bit (IPv6) identifier used in the

SESSION that remains constant over the life of the tunnel.
Normally it is set to all zero.; Ingress nodes that wish to
narrow the scope of a SESSION to the ingress-egress pair may
place their IP address here as a globally unique identifier.

IPv4 (or IPv6) tunnel sender address

IPv4 (or IPv6) address for a sender node.

LSP ID

A 16-bit identifier used in the SENDER_TEMPLATE and the
FILTER_SPEC, which can be changed to allow a sender to share
resources with itself.

The first three of these are in the SESSION object and are the basic
identification for the tunnel.; Setting the "Extended Tunnel ID" to
an IP address of the head-end LSR allows the scope of the SESSION to
be narrowed to only LSPs sent by that LSR.; A backup LSP is
considered part of the same session as its protected LSP; therefore
these three cannot be varied.

The last two are in the SENDER_TEMPLATE.; Multiple LSPs in the same
SESSION may be protected and may take different routes; this is
common when a tunnel is rerouted using make-before-break.; A backup
path must be clearly identified with its protected LSP to allow
correct merging and state treatment.; Therefore, a backup path must
inherit its LSP ID from the associated protected LSP.; Thus, the only
field in the SESSION and SENDER_TEMPLATE objects that could be varied
between a backup path and a protected LSP is the "IPv4 (or IPv6)
tunnel sender address" in the SENDER_TEMPLATE.

There are two different methods to uniquely identify a backup path,
described below.

6.1.1.; Backup Path Identification: Sender Template-Specific

In this approach, the SESSION object and the LSP_ID are copied from
the protected LSP.; The "IPv4 tunnel sender address" is set to an
address of the PLR.; If the head-end of a tunnel is also acting as
the PLR, it MUST choose an IP address different from the one used in
the SENDER_TEMPLATE of the original LSP tunnel.

When the sender template-specific approach is used, the protected
LSPs and the backup paths SHOULD use the Shared Explicit (SE) style.
This allows bandwidth sharing between multiple backup paths.; The

backup paths and the protected LSP MAY be merged by the Detour Merge
Points, when the ERO from the MP to the egress is the same on each
LSP to be merged, as specified in [RSVP-TE].

6.1.2.; Backup Path Identification: Path-Specific

In this approach, rather than vary the SESSION or SENDER_TEMPLATE
objects, an implementation uses a new object, the DETOUR object, to
distinguish between PATH messages for a backup path and the protected
LSP.

Thus, the backup paths use the same SESSION and SENDER_TEMPLATE
objects as the ones used in the protected LSP.; The presence of a
DETOUR object in Path messages signifies a backup path; the presence
of a FAST_REROUTE object and/or the "local protection requested" flag
in the SESSION_ATTRIBUTE object indicates a protected LSP.

In the path message-specific approach, an LSR merges Path messages
that are received with the same SESSION and SENDER_TEMPLATE objects
and that also have the same next-hop object.; Without this behavior,
it would be impossible to associate the multiple RESV messages with
the backup paths.; However, this merging behavior reduces the total
number of RSVP states inside the network at the expense of merging
LSPs with different EROs.

6.2.; Procedures for Backup Path Computation

Before a PLR can create a detour or a bypass tunnel, the desired
explicit route must be determined.; This can be done using a CSPF
(Constraint-based Shortest Path First) computation.; Before this CSPF
computation, the following information must be collected at a PLR:

- The list of downstream nodes that the protected LSP passes
through.; This information is readily available from the
RECORD_ROUTE objects during LSP setup.; This information is also
available from the ERO.; However, if the ERO contains loose
sub-objects, the ERO may not provide adequate information.

- The downstream links/nodes that we want to protect against.
Once again, this information is learned from the RECORD_ROUTE
objects.; Whether node protection is desired is determined by
the "node protection" flag in the SESSION_ATTRIBUTE object and
local policy.

- The upstream uni-directional links that the protected LSP passes

;;;;;through.; This information is learned from the RECORD_ROUTE
objects; it is only needed for setting up one-to-one protection.
In the path-specific method, it is necessary to avoid the detour
and the protected LSP sharing a common next-hop upstream of the
failure.; In the sender template-specific mode, this same
restriction is necessary to avoid sharing bandwidth between the
detour and its protected LSP, where that bandwidth has been
reserved only once.

- The link attribute filters to be applied.; These are derived
from the FAST_REROUTE object, if it is included in the PATH
message, or from the SESSION_ATTRIBUTE object otherwise.

- The bandwidth to be used is found in the FAST_REROUTE object, if
it is included in the PATH message, or in the SESSION_ATTRIBUTE
object otherwise.; Local policy may modify the bandwidth to be
reserved.

- The hop-limit, if a FAST_REROUTE object was included in the PATH
message.

When a CSPF algorithm is used to compute the backup route, the
following constraints must be satisfied:

- For detour LSPs, the destination MUST be the tail-end of the
protected LSP.; For bypass tunnels (Section 7), the destination
MUST be the address of the MP.

- When one-to-one protection is set up by using the path-specific
method, a detour MUST not traverse the upstream links of the
protected LSP in the same direction.; This prevents the
possibility of early merging of the detour into the protected
LSP.; When one-to-one protection is set up using the sender-
template-specific method, a detour should not traverse the
upstream links of the protected LSP in the same direction.; This
prevents sharing the bandwidth between a protected LSP and its
backup upstream of the failure where the bandwidth would be used

;;;;;twice in the event of a failure.

- The backup LSP cannot traverse the downstream node and/or link
whose failure is being protected against.; Note that if the PLR
is the penultimate hop, node protection is not possible, and
only the downstream link can be avoided.; The backup path may be
computed to be SRLG disjoint from the downstream node and/or
link being avoided.

- The backup path must satisfy the resource requirements of the
protected LSP.; This includes the link attribute filters,
bandwidth, and hop limits determined from the FAST_REROUTE
object and the SESSION_ATTRIBUTE object.

If such computation succeeds, the PLR should attempt to establish a
backup path.; The PLR may schedule a re-computation at a later time
to discover better paths that might have emerged.; If for any reason,
the PLR is unable to bring up a backup path, it must schedule a retry
at a later time.

6.3.; Signaling Backups for One-to-One Protection

Once a PLR has decided to protect an LSP locally with one-to-one
backup and has identified the desired path, it signals for the
detour.

The following describes the transformation to be performed upon the
protected LSP"s PATH message to create the detour LSP"s PATH message.

- If the sender template-specific method is to be used, then the
PLR MUST change the "IPv4 (or IPv6) tunnel sender address" of
the SENDER_TEMPLATE to an address belonging to the PLR that is
not the same as that used for the protected LSP.; Additionally,
the DETOUR object MAY be added to the PATH message.

- If the path-specific method is to be used, then the PLR MUST add
a DETOUR object to the PATH message.

- The SESSION_ATTRIBUTE flags "Local protection desired",
"Bandwidth protection desired", and "Node protection desired"
MUST be cleared.; The "Label recording desired" flag MAY be
modified.; If the Path Message contained a FAST_REROUTE object

;;;;;and the ERO is not completely strict, the Include-any, Exclude-
any, and Include-all fields of the FAST_REROUTE object SHOULD be
copied to the corresponding fields of the SESSION_ATTRIBUTE
object.

- If the protected LSP"s Path message contained a FAST_REROUTE
object, this object MUST be removed from the detour LSP"s PATH
message.

- The PLR MUST generate an EXPLICIT_ROUTE object toward the
egress.; First, the PLR must remove all sub-objects preceding
the first address belonging to the Merge Point.; Then the PLR
SHOULD add sub-objects corresponding to the desired backup path
between the PLR and the MP.

- The SENDER_TSPEC object SHOULD contain the bandwidth information
from the received FAST_REROUTE object, if included in the
protected LSP"s PATH message.

- The RSVP_HOP object containing one of the PLR"s IP address.

- The detour LSPs MUST use the same reservation style as the
protected LSP.; This must be correctly reflected in the
SESSION_ATTRIBUTE object.

Detour LSPs operate like regular LSPs.; Once a detour path is
successfully computed and the detour LSP is established, the PLR
need not compute detour routes again, unless (1) the contents of
FAST_REROUTE have changed or (2) the downstream interface and/or
the nexthop router for a protected LSP has changed.; The PLR may
recompute detour routes at any time.

6.3.1.; Make-before-Break with Detour LSPs

If the sender template-specific method is used, it is possible to do
make-before-break with detour LSPs.; This is done using two different
IP addresses belonging to the PLR (which were not used in the
SENDER_TEMPLATE of the protected LSP).; If the current detour LSP
uses the first IP address in its SENDER_TEMPLATE, then the new detour
LSP should be signaled by using the second IP address in its
SENDER_TEMPLATE.; Once the new detour LSP has been created, the

current detour LSP can be torn down.; By alternating the use of these
IP addresses, the current and new detour LSPs will have different
SENDER_TEMPLATES and, thus, different state in the downstream LSRs.

This make-before-break mechanism, which changes the PLR IP address in
the DETOUR object instead, is not feasible with the path-specific
method, as the PATH messages for new and current detour LSPs may be
merged if they share a common next-hop.

6.3.2.; Message Handling

LSRs must process the detour LSPs independently of the protected LSPs
to avoid triggering the LSP loop detection procedure described in
[RSVP-TE].

The PLR MUST not mix the messages for the protected and the detour
LSPs.; When a PLR receives Resv, ResvTear, and PathErr messages from
the downstream detour destination, the messages MUST not be forwarded
upstream.; Similarly, when a PLR receives ResvErr and ResvConf
messages from a protected LSP, it MUST not propagate them onto the
associated detour LSP.

A session tear-down request is normally originated by the sender via
PathTear messages.; When a PLR node receives a PathTear message from
upstream, it MUST delete both the protected and the detour LSPs.; The
PathTear messages MUST propagate to both protected and detour LSPs.
During error conditions, the LSRs may send ResvTear messages to fix
problems on the failing path.; When a PLR node receives the ResvTear
messages from downstream for a protected LSP, as long as a detour is
up, the ResvTear messages MUST not be sent further upstream.
PathErrs should be treated similarly.

6.3.3.; Local Reroute of Traffic onto Detour LSP

When the PLR detects a failure on the protected LSP, the PLR MUST
rapidly switch packets to the protected LSP"s backup LSP instead of
to the protected LSP"s normal out-segment.; The goal of this method
is to effect the redirection within 10s of milliseconds.

L32;;;L33;;;L34;;;L35
R1-------R2-------R3-------R4-------R5

L46;L44

L47;;;;
R6----------------R7

Protected LSP: [R1->R2->R3->R4->R5]
Detour LSP:;[R2->R6->R7->R4]

Example 3.; Redirect to Detour

In Example 3, if the link [R2->R3] fails, R2 would do the following.
Any traffic received on link [R1->R2] with label L32 would be sent on
link [R2->R6] with label L46 (along the detour LSP) instead of on
link [R3->R4] with label L34 (along the protected LSP).; The merge
point R4 would recognize that packets received on link [R7->R4] with
label L44 should be sent on link [R4->R5] with label L35 and that
they should be merged with the protected LSP.

6.4.; Signaling for Facility Protection

A PLR may use one or more bypass tunnels to protect against the
failure of a link and/or a node.; These bypass tunnels may be set up
in advance or may be dynamically created as new protected LSPs are
signaled.

6.4.1.; Discovering Downstream Labels

To support facility backup, the PLR must determine a label that will
indicate to the MP that packets received with that label should be
switched along the protected LSP.; This can be done without
explicitly signaling the backup path if the MP uses a label space
global to that LSR.

As described in Section 6, the head-end LSR MUST set the "label
recording requested" flag in the SESSION_ATTRIBUTE object for LSPs
requesting local protection.; This will cause (as specified in
[RSVP-TE]) all LSRs to record their INBOUND labels and to note via a
flag whether the label is global to the LSR.; Thus, when a protected
LSP is first signaled through a PLR, the PLR can examine the RRO in
the Resv message and learn about the incoming labels that are used by
all downstream nodes for this LSP

When MPs use per-interface label spaces, the PLR must send Path
messages (for each protected LSP using a bypass tunnel) via that
bypass tunnel prior to the failure in order to discover the
appropriate MP label.; The signaling procedures for this are in

Section 6.4.3 below.

6.4.2.; Procedures for the PLR before Local Repair

A PLR that determines to use facility-backup to protect a given LSP
should select a bypass tunnel to use, taking into account whether
node protection is to be provided, what bandwidth was requested,
whether a bandwidth guarantee is desired, and what link attribute
filters were specified in the FAST_REROUTE object.; The selection of
a bypass tunnel for a protected LSP is performed by the PLR when the
LSP is first set up.

6.4.3.; Procedures for the PLR during Local Repair

When the PLR detects a link or/and node failure condition, it has to
reroute the data traffic onto the bypass tunnel and to start sending
the control traffic for the protected LSP onto the bypass tunnel.

The backup tunnel is identified by using the sender template-specific
method.; The procedures to follow are similar to those described in
Section 6.3.

- The SESSION is unchanged.

- The SESSION_ATTRIBUTE is unchanged except as follows:; The
"Local protection desired", "Bandwidth protection desired", and
"Node protection desired" flags SHOULD be cleared.; The "Label
recording desired" MAY be modified.

- The IPv4 (or IPv6) tunnel sender address of the SENDER_TEMPLATE
is set to an address belonging to the PLR.

- The RSVP_HOP object MUST contain an IP source address belonging
to the PLR.; Consequently, the MP will send messages back to the
PLR with that IP address as the destination.

- The PLR MUST generate an EXPLICIT_ROUTE object toward the
egress.; Detailed ERO processing is described below.

- The RRO object may have to be updated as described in Section
6.5.

The PLR sends Path, PathTear, and ResvConf messages via the backup
tunnel.; The MP sends Resv, ResvTear, and PathErr messages by sending
them directly to the address in the RSVP_HOP object, as specified in
[RSVP].

If it is necessary to signal the backup prior to failure to determine
the MP label to use, then the same Path message is sent.; In this
case, the PLR SHOULD continue to send Path messages for the protected

LSP along the normal route.; PathTear messages should be duplicated,
with one sent along the normal route and one sent through the bypass
tunnel.; The MP should duplicate the Resv and ResvTear messages and
send them to both the PLR and the LSR indicated by the protected
LSP"s RSVP_HOP object.

6.4.4.; Processing Backup Tunnel"s ERO

Procedures for ERO processing are described in [RSVP-TE].; This
section describes additional ERO update procedures for Path messages
that are sent over bypass tunnels.; If normal ERO processing rules
were followed, the Merge Point would examine the first sub-object and
likely reject it (Bad initial sub-object).; This is because the
unmodified ERO might contain the IP address of a bypassed node (in
the case of a NNHOP Bypass Tunnel) or of an interface that is
currently down (in the case of a NHOP Backup Tunnel).; For this
reason, the PLR invokes the following ERO procedures before sending a
Path message via a bypass tunnel.

Sub-objects belonging to abstract nodes that precede the Merge
Point are removed, along with the first sub-object belonging to
the MP.; A sub-object identifying the Backup Tunnel destination is
then added.

More specifically, the PLR MUST:

- remove all the sub-objects proceeding the first address
belonging to the MP, and

- replace this first MP address with an IP address of the MP.
(Note that this could be same address that was just removed.)

6.5.; PLR Procedures during Local Repair

In addition to the method-specific signaling and packet treatment,
there is common signaling that should be followed.

During fast reroute, for each protected LSP containing an RRO object,
the PLR obtains the RRO from the protected LSP"s stored RESV.; The
PLR MUST update the IPv4 or IPv6 sub-object it inserted into the RRO
by setting the "Local protection in use" and "Local Protection
Available" flags.

6.5.1.; Notification of Local Repair

In many situations, the route used during local repair will be less
than optimal.; The purpose of local repair is to keep high priority
and loss-sensitive traffic flowing while a more optimal re-routing of