Network Working Group J. Chapman
Request For Comments: 1841 Cisco Systems, Inc.
Category: Informational D. Coli
Cisco Systems, Inc.
A. Harvey
Cisco Systems, Inc.
B. Jensen
Cisco Systems, Inc.
K. Rowett
Cisco Systems, Inc.
September 1995
PPP Network Control Protocol for LAN Extension
Status of Memo
This memo provides information for the Internet community. This memo
does not specify an Internet standard of any kind. Distribution of
this memo is unlimited.
Abstract
Telecommunications infrastrUCture is improving to offer higher
bandwidth connections at lower cost. Access to the network is
changing from modems to more intelligent devices. This informational
RFCdiscusses a PPP Network Control Protocol for one such intelligent
device. The protocol is the LAN extension interface protocol.
Table of Contents
1.0 Introduction ........................................... 3
1.1 LAN Extension Interface Topology ..................... 4
1.2 LAN Extension Interface Architecture ................. 5
1.3 LAN Extension Interface Protocol ..................... 6
2.0 LAN Extension Interface Protocol Control Packets........ 8
2.1 Startup Options ...................................... 8
2.2 Remote Command Options ............................... 14
2.3 Conditions for Sending PPP-LEX Packet ................ 17
3.0 Filter Protocol Type ................................... 18
3.1 LEX_RCMD_REQUEST - Filter Protocol Type............... 19
3.2 Response Packets - Filter Protocol Type............... 21
4.0 Filter MAC Address ..................................... 22
4.1 LEX_RCMD_REQUEST - Filter MAC Address ................ 23
4.2 Response Packets - Filter MAC Address................. 25
5.0 Set Priority ........................................... 27
5.1 LEX_RCMD_REQUEST - Set Priority ...................... 27
5.2 Response Packets - Set Priority ...................... 29
6.0 Disable LAN Extension Ethernet Interface ............... 30
6.1 LEX_RCMD_REQUEST - Disable LAN Extension
Ethernet Interface ................................... 31
6.2 Response Packets - Disable LAN Extension
Ethernet Interface ................................... 32
7.0 Enable LAN Extension Ethernet Interface ................ 33
7.1 LEX_RCMD_REQUEST - Enable LAN Extension
Ethernet Interface ................................... 33
7.2 Response Packets - Enable LAN Extension
Ethernet Interface ................................... 34
8.0 Reboot LAN Extension Interface Unit .................... 35
8.1 LEX_RCMD_REQUEST - Reboot LAN Extension Interface
Unit ................................................. 35
8.2 Response Packets - Reboot LAN Extension
Interface Unit ....................................... 36
9.0 Request Statistics ..................................... 37
9.1 LEX_RCMD_REQUEST - Request Statistics ................ 37
9.2 LEX_RCMD_ACK - Request Statistics .................... 39
9.3 LEX_RCMD_NAK/LEX_RCMD_REJ - Request Statistics ....... 44
10.0 Download Request ...................................... 45
10.1 LEX_RCMD_REQUEST - Download Request ................. 46
10.2 Response Packets - Download Request.................. 48
11.0 Download Data ......................................... 49
11.1 LEX_RCMD_REQUEST - Download Request ................. 49
11.2 Response Packets - Download Data .................... 51
12.0 Download Status ....................................... 52
12.1 LEX_RCMD_REQUEST - Download Status .................. 53
12.2 LEX_RCMD_ACK - Download Status ...................... 54
12.3 LEX_RCMD_NAK/LEX_RCMD_REJ - Download Status ......... 56
13.0 Inventory Request ..................................... 56
13.1 LEX_RCMD_REQUEST - Inventory Request ................ 57
13.2 LEX_RCMD_ACK - Inventory Request .................... 58
13.3 LEX_RCMD_NAK/LEX_RCMD_REJ - Inventory Request ....... 61
14.0 LAN Extension Interface Protocol Data Packets ......... 62
14.1 Frame Format ........................................ 62
14.2 Summary Field Descriptions........................... 63
NOTES ...................................................... 65
REFERENCES ................................................. 65
SECURITY CONSIDERATIONS .................................... 66
AUTHORS" ADDRESSES ......................................... 66
1.0 Introduction
An increasing number of corporations allow their employees to
telecommute to work due to local government regulations on traffic
and air pollution. Additionally, many businesses are run out of
internetworked home Offices and small branch offices. With these
changes in the workplace, more people and businesses require Internet
access from small LANs.
Today, routers serve the LAN-to-LAN traffic using high-speed WAN
links such as leased lines, ISDN, or Frame Relay. This new breed of
Internet users from home offices and small branch offices may have a
different, less network-literate skill set than those connecting up
to the Internet today. These new users need an alternative to the
complex and hard-to-configure routers currently employed for
connectivity. One such alternative is a LAN extension interface unit.
A LAN extension interface unit is a hardware device installed at
remote sites (such as a home office or small branch office) that
connects a LAN across a WAN link to a router at a central site. The
following sections introduce a LAN extension interface topology,
architecture, and protocol.
1.1 LAN Extension Interface Topology
Figure 1 shows the topology of LAN extension interfaces. The figure
shows two LAN extension interface units connected via a WAN link to a
central or "host router."
Figure 1 LAN Extension Interface Topology
-----------------------------------------
Router
-----------------------------------------
Virtual Interface Virtual Interface
123.123.78.1 123.123.89.1
.........................................
Serial 0 Serial n
-----------------------------------------
<---- WAN Link ---->
------------------ ------------------
LAN Extension LAN Extension
Interface Unit Interface Unit
------------------ ------------------

------------------ ------------------

------------ ------------
End node End node
------------ ------------
123.123.78.2 123.123.46.2
Each LAN extension interface unit maps to a virtual interface at the
host router. The virtual interface mirrors the characteristics of the
LAN extension interface unit. To the routing protocols, the virtual
interface looks just like a local interface, but with the bandwidth
of a serial line. The virtual interface keeps the state (up or down)
of the LAN extension interface unit, and identifies each LAN
extension interface unit by its MAC address.
A LAN extension interface protocol transfers MAC frames from the LAN
extension interface unit across the serial line to the host router.
At the termination point in the router, the router routes the
packets. This topology uses only one subnet per remote LAN rather
than two, as is the case when routers exist on both ends of a WAN
link. Figure 1 shows this subnetting structure. The IP addresses of
the virtual interfaces on the router are in the same subnet as the IP
addresses of the end nodes on the LAN of the LAN extension interface
unit. The LAN extension interface unit itself has no IP address.
LAN extension interface units resemble bridges, but with the
following distinct differences:
* LAN extension interface units always depend on a host router.
They cannot operate standalone or even back-to-back with other
LAN extension interface units.
* LAN extension interface units need not employ any spanning tree
algorithm.
* (LAN extension interface units transfer MAC frames across a
serial line (like bridges), but a router can either route or
bridge the LAN extension interface data packets.
1.2 LAN Extension Interface Architecture
Figure 2 shows the basic LAN extension interface architecture.
Figure 2 LAN Extension Interface Architecture
Router LAN Extension Interface
------------------- -------------------
Network Layer MAC Layer
------------------- -------------------

------------------- -------------------
Virtual Interface Filters
------------------- -------------------

------------------- -------------
PPP RCMD
Handler
------------------- -------------

------------------- -------------------
Serial Interface PPP
------------------- -------------------

-------------------
Serial Interface
-------------------
WAN Link
---------------------------------------

Outbound Inbound
--------------> <---------------
In the inbound direction (from the remote LAN, to the LAN extension
interface unit, across the WAN link, to the host router), the LAN
extension interface unit can filter received frames to optimize WAN
utilization. The LAN extension interface unit can filter frames by
protocol type or by MAC address. Frames that pass through the LAN
extension interface filters go to the WAN protocol state machine. In
Figure 2, this state machine is PPP. The LAN extension interface unit
adds PPP encapsulation and forwards the packet to the router via the
WAN serial link.
Upon receiving the frame, the host router decapsulates the PPP header
and passes the packet to the virtual interface. From there the
virtual interface handles the packet like any packet received on a
local interface -- by routing or bridging the packet to another
interface, depending on configuration.
In the outbound direction (from the host router, across the WAN link,
to the LAN extension interface unit, to the LAN), the host router"s
virtual interface builds the full MAC header, before adding PPP
encapsulation. The router then sends the packet across the WAN serial
link to the LAN extension interface unit. The LAN extension interface
unit strips the PPP header and forwards the packet directly onto the
LAN. The host router has already determined that the packet needs to
be forwarded to the LAN extension interface unit, hence there is no
need for additional filtering or processing at that end.
Embedded in the data stream is a control stream for configuring and
managing the LAN extension interface unit from the host router. The
virtual interface makes the remote LAN extension interface unit
appear like a local router interface to the routing protocols.
Configuration commands and statistics gathering commands are issued
on the router to the virtual interface. The virtual interface formats
the LAN extension interface remote commands into encoded messages and
transfers them in-band with the data packets. The LAN extension
interface unit decodes the remote commands and executes them.
Responses are similarly formatted messages sent by the LAN extension
interface unit to the host router. The remote command messages use a
different encapsulation type than the data packets, as described
later in this document in the "LAN Extension Interface Protocol
Control Packets" and "LAN Extension Interface Protocol Data Packets"
sections.
1.3 LAN Extension Interface Protocol
To accommodate this LAN extension interface architecture, a new
Network Control Protocol (NCP) for PPP exists. This NCP is called
PPP-LEX. The basic functionality of PPP-LEX is to encapsulate LAN
extension interface control and data packets. The IETF has assigned
two new protocol types for these functions, as shown in Table 1.
Table 1 IETF Protocol Types for PPP-LEX
Protocol Type Function
0x8041 Encapsulates control packets
0x0041 Encapsulates data packets (MAC frames)
PPP is a natural choice for a LAN extension interface protocol
because it allows for negotiating a specific control protocol and
options at connection time. This means that network administrators do
not have to statically configure the router interface for remote
interfaces. Rather, remote interfaces negotiate the link at
connection time.
The LAN extension interface protocol employs PPP link operation as
described in RFC1331, which reads as follows:
In order to establish communications of a point-to-point link,
each end of the PPP link must first send [Link Control Protocol]
LCP packets to configure and test the data link. After the link
has been established,the peer may be authenticated. Then PPP must
send NCP packets to choose and configure one or more network layer
protocols. Once each of the chosen network-layer protocols has
been configured, datagrams from each network layer protocol can be
sent over the link.
The link will remain configured for communications until eXPlicit
LCP or NCP packets close the link down, or until some external
event occurs (an inactivity timer expires or network administrator
intervention). (References, [1])
Thus, the LAN extension interface unit and the host router exchange
PPP-LCP packets at connection time to dynamically configure and test
the WAN serial link. Once the link reaches an "opened" state, the LAN
extension interface unit and host router exchange PPP-LEX NCP packets
to configure the LAN extension interface protocol. Once it is
configured, the NCP (PPP-LEX) reaches an "opened" state, and PPP
carries the PPP-LEX control and data packets across the serial link.
At this point, link traffic is a any combination of LCPs, PPP-LEX
NCPs, PPP-LEX control packets, and PPP-LEX data packets.
Note that the LAN extension interface protocol is not a bridging
protocol. The only similarity to the PPP Bridging Control Protocol
(References. [2]) is that the LAN extension interface protocol also
encapsulates MAC frames.
The following sections detail PPP-LEX control packets and data
packets.
2.0 LAN Extension Interface Protocol Control Packets
There are two types of PPP-LEX control packets, as follows:
* Startup options packet
* Remote command options packets
The startup options packet is the first PPP-LEX NCP packet that the
LAN extension interface unit sends to the host router after the LCP
has reached an "opened" state. This required startup options packet
configures the LAN extension interface protocol and puts the PPP-LEX
NCP in an "opened" state.
Remote command options are the PPP-LEX NCP packets that control the
functioning and statistics gathering of the LAN extension interface
protocol.
2.1 Startup Options
The LAN extension interface unit sends a startup options packet to
the host router to negotiate the following startup options:
* MAC Type
* MAC Address
* LAN Extension
The MAC Type startup option informs the host router of the type of
media that the LAN extension interface unit is connected to. For
example, the LAN extension interface unit may be connected to an
Ethernet LAN or a Token Ring LAN. Currently, only Ethernet is
supported. The MAC type tells the host router what type of traffic
the LAN extension interface unit is prepared to receive. If the host
router rejects the MAC type, the LAN extension interface unit sends
the Configure-Request again.
The MAC Address startup option sends the MAC address of the LAN
extension interface unit to the host router to authenticate the LAN
extension interface unit and bind it to the corresponding virtual
interface at the host router. The host router also inserts the MAC
address in outbound packets. The MAC address is represented in IEEE
802.3 canonical format.
The LAN Extension startup option establishes the network layer
protocol (NCP) as PPP-LEX and provides the host router with the LAN
extension interface protocol version number.
Each startup option is transmitted in a series of three fields:
Option-Type, Option-Length, and Option-Data fields. The fields are
concatenated in the startup options Configure-Request packet.
Frame Format
Figure 3 shows a summary of the frame format for the startup options
packet. The LAN extension interface unit sends this startup options
packet to the host router. The LAN extension interface unit transmits
these fields from left to right.
Figure 3 Startup Options Frame Format (Configure-Request)
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Control Protocol Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1) (2)
LAN Extension Interface Startup Options
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Length Option-Data
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1)
Address
This PPP-specified field is one octet and contains the binary
sequence 11111111 (hexadecimal 0xFF), the All-Stations address. PPP
does not assign individual station addresses. The All-Stations
address must be recognized and received by all devices. For more
information on this field, refer to "The Point-to-Point Protocol
(PPP) for the Transmission of Multi-protocol Datagrams over Point-
to-Point Links." (References, [1])
Control
This PPP-specified field is one octet and contains the binary
sequence 00000011 (hexadecimal 0x03), the Unnumbered Information (UI)
command with the P/F bit set to zero.
For more information on this field, refer to "The Point-to-Point
Protocol (PPP) for the Transmission of Multi-protocol Datagrams over
Point-to Point Links." (References, [1])
Protocol-Type
The Protocol-Type field is two octets and contains the IETF-assigned
protocol type value. Valid LAN extension interface protocol type
values are as follows:
* 0x8041 (for control packets)
* 0x0041 (for data packets)
Because the startup options packet encapsulates LAN extension
interface control data, the valid value for this field is 0x8041.
Code
The Code field is one octet and identifies the type of LCP packet
that the LAN extension interface packet is sending. Valid values are
as follows:
* 0x01 - Configure-Request
* 0x02 - Configure-Ack
* 0x03 - Configure-Nak
* 0x04 - Configure-Rej
The LAN extension interface unit initiates the startup options
packet; therefore, the valid value for this field is 1.
Identifier
The Identifier field is one octet and contains a randomly generated
value. The value aids matching requests and replies. It is
recommended that a non-zero value be used for the identifier. That
is, zero could be used in the future for unsolicited messages from
the LAN extension interface unit. Valid values are 0x01-0xFF.
Length
The Length field is two octets and indicates the length of the entire
packet in octets, including the Code, Identifier, Length, and startup
options fields.
Option-Type
The Option-Type field is one octet and identifies the startup option
being negotiated. Valid values are as follows:
* 0x01 - MAC Type
* 0x03 - MAC Address
* 0x05 - LAN Extension
Option-Length
The Option-Length field is one octet and specifies the length of the
startup option fields, including the Option-Type, Option-Data, and
Option-Length fields.
Option-Data
The Option-Data field contains the data relating to the value
specified in the Option-Type field. That is, if the Option-Type field
specifies MAC type (0x01), then the Option-Data field contains the
MAC type (Ethernet, Token Ring, and so on). If the Option-Type field
specifies MAC address (0x03), then the Option-Data field contains the
actual MAC address. If the Option-Type field specifies LAN Extension
(0x05), then the Option-Data field contains LAN extension interface
software information. The following table defines the contents of the
Option-Data field for each possible Option-Type field value:
Option-Type Field Value Option-Data
0x01 (MAC Type) The most up-to-date value of the MAC type as
specified in the most recent "Assigned
Numbers" RFC. The current valid value from
that RFCfollows:
* 0x01: IEEE 802.3/Ethernet with canonical
addresses
0x03 (MAC Address) The burned-in MAC address in IEEE 802.3
canonical format.
0x05 (LAN Extension) The LAN extension interface protocol version
number. 0x01 is the current protocol version
supported.
Example
In the Configure-Request packet that it sends to the host router, the
LAN extension interface unit concatenates the Option-Type, Option-
Data, and Option-Length fields for each startup option, as shown in
Figure 4. The LAN extension interface unit transmits these fields
from left to right.
Figure 4 Sample Startup Options Configure-Request Packet
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF 0x03 0x8041
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Control Protocol-Type
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x01 0x09 0x12
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Identifier Length
LAN Extension Interface Startup Options
<------------------------------------------------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x01 0x03
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Length
------------------------------>
4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x01
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Data
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x03 0x08
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Length
4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0A 0A 0A 0A 0B 0C
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
---------- Option-Data --------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x05 0x03
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Length
4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0x01
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Data
In Figure 4, the Address field always contains 0xFF, and the Control
field always contains 0x03. The Protocol-Type field value is 0x8041
because the startup options packet is a LAN extension interface
control packet. The Code field value is 0x01 because the LAN
extension interface unit is sending an LCP Configure-Request packet
to configure or negotiate PPP-LEX. The Identifier field contains a
randomly generated number. The Length field gives the total length of
the entire packet.
The first startup option is the MAC Type startup option. The Option-
Type value for MAC Type is 0x01. The Option-Length field value for
the MAC type startup option is 3 octets. The Option-Data field value
is 0x01 because, in this example, the LAN extension interface unit
connects to an Ethernet LAN using 802.3 canonical addresses.
The next startup option transmitted is the MAC Address. Its Option-
Type field value is 0x03, its Option-Length field value is 8 octets,
and its Option-Data field value is the actual MAC address.
Lastly, the LAN Extension startup option is transmitted. Its Option-
Type field value is 0x05, its Option-Length field value is 3 octets,
and its Option-Data field value is the LAN extension interface
protocol version number (0x01).
The host router responds to this LCP Configure-Request packet with an
LCP Configure-Ack packet, Configure-Nak packet, or Configure-Rej
packet. For more information on these packets, refer to "The Point-
to-Point Protocol (PPP) for the Transmission of Multi-protocol
Datagrams over Point-to-Point Links" RFC. (References, [1])
2.2 Remote Command Options
Once the host router responds to the startup options Configure-
Request packet with a Configure-Ack packet, the PPP-LEX NCP is in an
"opened" state, and the LAN extension interface unit and the host
router freely exchange PPP-LEX data packets and remote command
options packets.
The host router initiates PPP-LEX remote command options packets to
control the configuration of the LAN extension interface unit and to
gather statistics. There are 11 types of remote command options that
the host router can send in a LEX_RCMD_REQUEST packet to the LAN
extension interface unit. The LAN extension interface unit responds
to a LEX_RCMD_REQUEST packet with a LEX_RCMD_ACK, LEX_RCMD_NAK, or
LEX_RCMD_REJ packet.
Frame Format
Figure 5 shows a summary of the frame format for a remote command
options packet. These fields are transmitted from left to right.
Figure 5 Remote Command Options Frame Format
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Address Control Protocol Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1) (2)
LAN Extension Interface Remote Command Options
<--------------------------------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1 octet) (1)
---------------------------------------------->
6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Length Option-Data
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2)
Address
This PPP-specified field is a single octet and contains the binary
sequence 11111111 (hexadecimal 0xFF), the All-Stations address. PPP
does not assign individual station addresses. The All-Stations
address must be recognized and received by all devices. For more
information on this field, refer to "The Point-to-Point Protocol
(PPP) for the Transmission of Multi-protocol Datagrams over Point-
to-Point Links." (References, [1])
Control
This PPP-specified field is a single octet and contains the binary
sequence 00000011 (hexadecimal 0x03), the Unnumbered Information (UI)
command with the P/F bit set to zero.
For more information on this field, refer to "The Point-to-Point
Protocol (PPP) for the Transmission of Multi-protocol Datagrams over
Point-to Point Links." (References, [1])
Note: Hereafter the Address and Control fields will be represented
together as a 2-octet field containing "0xFF03".
Protocol-Type
The Protocol-Type field is two octets and contains the IETF-assigned
protocol type value. Valid LAN extension interface protocol type
values follow:
* 0x8041 (for control packets)
* 0x0041 (for data packets)
Because the remote command options packet encapsulates LAN extension
interface control data, the valid value for this field is 0x8041.
Code
The Code field is one octet and identifies the type of PPP-LEX
packet. Valid values are as follows:
* 0x40 - LEX_RCMD_REQUEST packet
* 0x41 - LEX_RCMD_ ACK packet
* 0x42 - LEX_RCMD_NAK packet
* 0x43 - LEX_RCMD_REJ packet
The host router sends the LEX_RCMD_REQUEST packet, and the LAN
extension interface unit sends the LEX_RCMD_ACK, LEX_RCMD_NAK, and
LEX_RCMD_REJ packets.
Identifier
The Identifier field is one octet and contains a randomly generated
value. The value aids matching requests and replies. It is
recommended that a non-zero value be used for the identifier. That
is, zero could be used in the future for unsolicited messages from
the LAN extension interface unit. Valid values are 0x01-0xFF.
Length
The Length field is two octets and indicates the length in octets of
the entire packet, including the Code, Identifier, Length, and remote
command options fields.
Option-Type
The Option-Type field is one octet and identifies the remote command
option being transmitted. Valid values are as follows:
* 0x01 - Filter Protocol Type
* 0x02 - Filter MAC Address
* 0x03 - Set Priority
* 0x04 - Disable LAN Extension Ethernet Interface
* 0x05 - Enable LAN Extension Ethernet Interface
* 0x06 - Reboot LAN Extension Interface Unit
* 0x07 - Request Statistics
* 0x08 - Download Request
* 0x09 - Download Data
* 0x0A - Download Status
* 0x0B- Inventory Request
Each remote command option is discussed in detail in its own section
later in this document.
Option-Flags
This field is one octet and further specifies the remote command
option, containing specific actions that must be followed.
Option-Length
The Option-Length field is two octets and specifies the length in
octets of the remote command option fields, including the Option-
Type, Option-Flags, Option-Length, and Option-Data fields.
Option-Data
Option-Data field contains data relating to the remote command option
specified in the Option-Type field.
2.3 Conditions for Sending PPP-LEX Packet
This section describes the general conditions under which PPP-LEX
packet types are sent. For specific information by remote command,
refer to the appropriate remote command section later in this
document.
LEX RCMD_REQUEST Packet
The host router sends LEX_RCMD_REQUEST packets to the LAN extension
interface unit to initiate a remote command request. Until the host
router receives a LEX_RCMD_ACK, LEX_RCMD_NAK, or LEX_RCMD_REJ packet
from the LAN extension interface unit, the host router continues to
send the LEX_RCMD_REQUEST packet a default number of times, at which
point the host router times out.
LEX_RCMD_ACK Packet
The LAN extension interface unit responds to a LEX_RCMD_REQUEST
packet with a LEX_RCMD_ACK packet when it correctly receives the
request and is able to perform the request.
LEX RCMD_NAK Packet
The LAN extension interface unit responds to a LEX_RCMD_REQUEST
packet with a LEX_RCMD_NAK packet when the LAN extension interface
unit recognizes all the elements of the remote command option, but
some elements are not acceptable. Upon receipt of a LEX_RCMD_NAK
packet, the host router immediately stops sending the request.
LEX RCMD_REJ Packet
The LAN extension interface unit responds to a LEX_RCMD_REQUEST
packet with a LEX_RCMD_REJ packet when the Option-Type value in the
request packet is invalid. Invalid Option-Type values are those less
than 0x01 or greater than 0x0B. Currently, this is the only condition
under which the LAN extension interface unit sends a LEX_RCMD_REJ
packet. Upon receipt of a LEX_RCMD_REJ packet, the host router
immediately stops sending the request.
The following sections detail each of the 11 remote command options.
The sections provide a general description of the option and then
specify the option"s Option-Type, Option-Flags, Option-Length, and
Option-Data fields. In addition, the sections describe the return
messages from the LAN extension interface unit.
3.0 Filter Protocol Type
The host router sends a LEX_RCMD_REQUEST packet with an Option-Type
of 0x01 to the LAN extension interface unit to configure the LAN
extension interface unit to filter inbound packets by protocol type.
A protocol type filter determines whether or not the LAN extension
interface unit forwards packets of a specific protocol type to the
host router. A protocol type filter consists of a 16-bit value, 16-
bit mask, and a permit or deny field. (See the "Option-Data Field
Descriptions" section for more information on these filter fields.)
A LEX_RCMD_REQUEST packet can contain 0 to 200 (depending on MTU
size) protocol type filters. When a LEX_RCMD_REQUEST packet contains
multiple filters, they are concatenated.
The LAN extension interface unit applies the protocol type filters to
each inbound packet"s protocol type field in the order in which the
filters exist in the filter table. A packet must be permitted by one
of the filters before the LAN extension interface unit can forward
the packet across the serial link.
The following example is a filtering algorithm:
if (protocol_type_field & (~filter_mask)) == filter_value)
if (permit/deny_field == PERMIT) <forward packet on serial LAN>
else <DROP PACKET>
The protocol type filter should also be applied to the DIX type code
field of Ethernet II frames as well as to IEEE 802.2 SNAP packets.
3.1 LEX RCMD_REQUEST-Filter Protocol Type
Figure 6 shows a frame format summary of a LEX_RCMD_REQUEST packet
for the Filter Protocol Type remote command option. The host router
transmits the fields from left to right.
Figure 6 LEX_RCMD_REQUEST Packet Frame Format - Filter Protocol Type
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF03 Protocol-Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2 octets) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
LAN Extension Interface Remote Command Options
<--------------------------------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1)
---------------------------------------------->
6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Length Option-Data
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2)
Where the Option-Data field contains the following fields:
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Value (16 bits) Value (16 bits)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Permit/Deny (16 bits)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Summary Field Descriptions
For a complete description of the fields in the PPP Header, the LAN
Extension Interface Protocol Header, and the LAN Extension Interface
Remote Command Options, refer to the "Remote Command Options" section
earlier in this document. The following table provides a summary of
these fields when sending a LEX_RCMD_REQUEST packet that configures
the LAN extension interface unit to filter by protocol type.
Table 2 Field Values for LEX_RCMD_REQUEST Packet-Filter Protocol Type
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code 0x40 (LEX_RCMD_REQUEST packet)
Identifier Valid values: 0x01-0xFF
Length Minimum length = 12 octets
Maximum length = 1212 octets
Option-Type 0x01 (Filter Protocol Type)
Option-Flags None
Option-Length Minimum length = 4 octets
Maximum length = 1204 octets
Option-Data Zero or more filters to be applied at
the LAN extension interface unit. See the
following "Option-Data Field Descriptions"
for details.
Option-Data Field Descriptions
The following three Option-Data fields are used in conjunction to
specify a protocol type filter:
* Value
The Value field contains a 16-bit value that is any Ethernet type
code. Refer to the "Assigned Numbers" RFCfor valid Ethernet type
codes. (References, [4]).
* Mask
The Mask field contains a 16-bit "wild card" mask. That is, this
field contains a 16-bit number whose ones bits correspond to the type
code bits to be ignored during the comparison. Thus, the mask
excludes bits from the comparison in the protocol type filter.
* Permit/Deny
The Permit/Deny field determines whether a protocol type filter
permits or denies inbound frames to pass to the host router. A permit
value is a non-zero value that allows frames of a specific protocol
type to pass to the host router. A deny value is a zero value that
does not allow frames of a specific protocol type to pass to the host
router.
Implementation Notes
Each LEX_RCMD_REQUEST packet is a complete specification of all
protocol type filters and replaces any previously established
filters.
Note the following special cases:
* A LEX_RCMD_REQUEST packet with an Option-Length field equal
to four (without any filter entries) instructs the LAN extension
interface unit to turn off protocol type filtering. All MAC
protocol types are forwarded.
* A LEX_RCMD_REQUEST packet with a filter entry of 0x0000 in the
Value field, 0xFFFF in the Mask field, and a positive value in the
Permit/Deny field means that if previous filters in the filter list
do not permit the inbound packet then this filter entry will. This
filter entry is typically the last filter in a list of filters
contained within the Option-Data field.
* A LEX_RCMD_REQUEST packet with a filter entry of 0x0000 in the
Value field, 0xFFFF in the Mask field, and a zero in the
Permit/Deny field, means that the LAN extension interface unit must
deny all protocol types. This filter is typically the last filter in
a list of filters contained within the Option-Data field.
3.2 Response Packets - Filter Protocol Type
The following packets are valid responses to the Filter Protocol Type
LEX_RCMD_REQUEST packet:
* LEX_RCMD_ACK - Filter Protocol Type
The LAN extension interface unit sends a LEX_RCMD_ACK packet in
response to the Filter Protocol Type LEX_RCMD_REQUEST packet when the
LAN extension interface unit correctly receives the Filter Protocol
Type remote command option and applies all filter entries to its
filter table. All filter entries are returned to the host router in
the LEX_RCMD_ACK packet.
* LEX_RCMD_NAK - Filter Protocol Type
The LAN extension interface unit sends a LEX_RCMD_NAK packet in
response to the Filter Protocol Type LEX_RCMD_REQUEST packet when the
request contains an incorrect number of bytes in the filter or when
there are no more filter entries available. The LAN extension
interface unit continues to use the previous filter table (that is,
the filter table that existed prior to the receipt of the request).
The host router should signal an error to the user/network
administrator. All filter entries are returned to the host router in
the LEX_RCMD_NAK packet.
* LEX_RCMD-REJ - Filter Protocol Type
See the "Conditions for Sending PPP-LEX Packets" section earlier in
this document for more information on this packet type.
Table 3 summarizes the field values of Filter Protocol Type
LEX_RCMD_ACK, LEX_RCMD_NAK, and LEX_RCMD_REJ packets.
Table 3 Field Values for Response Packets - Filter Protocol Type
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code Valid values:
* 0x41 (LEX_RCMD_ACK packet)
* 0x42 (LEX_RCMD_NAK packet)
* 0x43 (LEX_RCMD_REJ packet)
Identifier The same value as that sent by the
LEX_RCMD_REQUEST packet
Length The same value as that sent by the
LEX_RCMD_REQUEST packet
Option-Type 0x01 (Filter Protocol Type)
Option-Flags None
Option-Length The same value as that sent by the
LEX_RCMD_REQUEST packet
Option-Data The filter entries sent in the
LEX_RCMD_REQUEST packet
4.0 Filter MAC Address
The host router sends a LEX_RCMD_REQUEST packet with an Option-Type
of 0x02 to the LAN extension interface unit to configure the LAN
extension interface unit to filter inbound packets by source MAC
address. A MAC address filter determines whether or not the LAN
extension interface unit forwards packets with a specific source MAC
address to the host router. A MAC address filter consists of MAC
address, a MAC address mask, and a permit or deny field. (See the
"Option-Data Field Descriptions" section later in this section for
more information on these filter fields.)
A LEX_RCMD_REQUEST packet can contain 0 to 100 (depending on MTU
size) MAC address filters. When a LEX_RCMD_REQUEST packet contains
multiple filters, they are concatenated.
The LAN extension interface unit applies MAC address filters to each
inbound packet"s source MAC address in the order in which the filters
exist in the filter entry list. A packet must be permitted by one of
the filters before the LAN extension interface unit can forward the
packet across the serial link.
4.1 LEX RCMD_REQUEST - Filter MAC Address
Figure 7 shows a frame format summary of a LEX_RCMD_REQUEST packet
for the Filter MAC Address remote command option. The host router
transmits the fields from left to right.
Figure 7 LEX_RCMD_REQUEST Packet Frame Format - Filter MAC Address
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF03 Protocol-Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2 octets) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
LAN Extension Interface Remote Command Options
<--------------------------------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1)
---------------------------------------------->
6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
Option-Length Option-Data
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
(2)
Where the Option-Data field contains the following fields:
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MAC Address (48 bits)....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MAC Address Mask (48 bits)....
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Permit/Deny (16 bits)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Summary Field Descriptions
For a complete description of the fields in the PPP Header, the LAN
Extension Interface Protocol Header, and the LAN Extension Interface
Remote Command Options, refer to the "Remote Command Options" section
earlier in this document. Table 4 provides a summary of these fields
when sending a LEX_RCMD_REQUEST packet that configures the LAN
extension interface unit to filter by source MAC address.
Table 4 Field Values for LEX_RCMD_REQUEST Packet - Filter MAC Address
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code 0x40 (LEX_RCMD_REQUEST packet)
Identifier Valid values: 0x01-0xFF
Length Minimum length = 12 octets
Maximum length = 1412 octets
Option-Type 0x02 (Filter MAC Address)
Option-Flags None
Option-Length Minimum length = 4 octets
Maximum length = 1404 octets
Option-Data Zero or more filters to be applied at the
LAN extension interface unit. See the
following "Option-Data Field Description
section for details.
Option-Data Field Descriptions
The following three Option-Data fields are used in conjunction to
specify a MAC address filter:
* MAC Address
The MAC Address field contains a 48-bit IEEE 802.3 MAC address in
canonical format.
* MAC Address Mask
The MAC Address Mask field contains a "wild card" mask. The mask is a
48-bit hexadecimal number whose ones bits correspond to the MAC
address bits to be ignored during the comparison. The mask excludes
bits from the comparison in the MAC address filter.
* Permit/Deny
The Permit/Deny field determines whether or not a MAC address filter
permits or denies inbound frames of a specific MAC address to pass to
the host router. A permit value is a non-zero value that allows
frames of a specific MAC address to pass to the host router. A deny
value is a zero value that does not allow frames of a specific MAC
address to pass to the host router.
Implementation Notes
Each LEX_RCMD_REQUEST packet is a complete specification of all MAC
address filters and replaces any previously established filters.
A LEX_RCMD_REQUEST packet with an Option-Length field equal to four
(without any filter entries) instructs the LAN extension interface
unit to turn off filtering. All MAC addresses, except local
destination addresses cached in the self-learning filter, are
forwarded.
4.2 Response Packets - Filter MAC Address
The following packets are valid responses to the Filter MAC Address
LEX_RCMD_REQUEST packet:
* LEX_RCMD_ACK - Filter MAC Address
The LAN extension interface unit sends a LEX_RCMD_ACK packet in
response to a Filter MAC Address LEX_RCMD_REQUEST packet when the LAN
extension interface unit correctly receives the Filter MAC Address
remote command option and applies the entries to its filter table.
All MAC address filter entries are returned in the LEX_RCMD_ACK
packet.
* LEX_RCMD_NAK - Filter MAC Address
The LAN extension interface unit sends a LEX_RCMD_NAK packet in
response to the Filter MAC Address LEX_RCMD_REQUEST packet when the
request contains an incorrect number of bytes in the filter or when
there are no more filter entries available. The LAN extension
interface unit continues to use the previous filter table (that is,
the filter table that existed prior to the receipt of the request).
The host router should signal an error to the user/network
administrator. All filter entries are returned in the LEX_RCMD_NAK
packet.
* LEX_RCMD-REJ - Filter MAC Address
See the "Conditions for Sending PPP-LEX Packets" section earlier in
this document for more information on this packet type.
Table 5 summarizes the field values of Filter MAC Address
LEX_RCMD_ACK, LEX_RCMD_NAK, and LEX_RCMD_REJ packets.
Table 5 Field Values for Response Packets - Filter MAC Address
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code Valid values:
* 0x41 (LEX_RCMD_ACK packet)
* 0x42 (LEX_RCMD_NAK packet)
* 0x43 (LEX_RCMD_REJ packet)
Identifier The same value as that sent by the
LEX_RCMD_REQUEST packet
Length The same value as that sent by the
LEX_RCMD_REQUEST packet
Option-Type 0x02 (Filter MAC Address)
Option-Flags None
Option-Length The same value as that sent by the
LEX_RCMD_REQUEST packet
Option-Data The filter entries sent in the
LEX_RCMD_REQUEST packet
5.0 Set Priority
The host router sends a LEX_RCMD_ REQUEST with an Option-Type of 0x03
to the LAN extension interface unit to establish the sending priority
of different protocol type packets from the LAN extension interface
unit to host router. There are four levels of priority:
* High
* Medium
* Normal
* Low
Packets are classified according to protocol type and then are queued
to one of four output queues on the LAN extension interface unit that
correspond to the above priority levels. When the LAN extension
interface unit is ready to transmit a packet, it scans the priority
queues in order, from the highest to lowest, to find the highest
priority packet.
5.1 LEX RCMD_REQUEST - Set Priority
To establish priority queues for each protocol type, the host router
sends a Set Priority LEX_RCMD_REQUEST packet. Figure 8 shows a frame
format summary of such a LEX_RCMD_REQUEST packet. The host router
transmits the fields from left to right.
Figure 8 LEX_RCMD_REQUEST Packet Frame Format - Set Priority
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF03 Protocol-Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2 octets) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
LAN Extension Interface Remote Command Options
<--------------------------------
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1)
---------------------------------------------->
6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
Option-Length Option-Data
-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
(2)
Where the Option-Data field contains the following fields:
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Protocol Type (16 bits) Protocol Value (16 bits)
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Summary Field Descriptions
For a complete descriptions of the fields in the PPP Header, the LAN
Extension Interface Protocol Header, and the LAN Extension Interface
Remote Command Options, refer to the "Remote Command Options" section
earlier in this document. The following table provides a summary of
these fields when sending a LEX_RCMD_REQUEST packet that sets
priority queuing.
Table 6 Field Values for LEX_RCMD_REQUEST Packet - Set Priority
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code 0x40 (LEX_RCMD_REQUEST packet)
Identifier Valid values: 0x01-0xFF
Length Minimum length = 12 octets
Maximum length = 1028 octets
Option-Type 0x03 (Set Priority)
Option-Flags None
Option-Length Minimum length = 4 octets
Maximum length = 1020 octets
Option-Data Protocol Type and Priority Value. See the
following "Option-Data Field Description"
section for details.
Option-Data Field Descriptions
The following Option-Data fields set the priority queuing of
different protocol type packets.
* Protocol Type
The Protocol Type field contains a 16-bit number that is any Ethernet
type code. See the most recent "Assigned Numbers" RFCfor the correct
Ethernet type code.
* Priority Value
The Priority Value field specifies the priority queue for the
protocol type specified in the Protocol Type field. Valid values are
as follows:
- 0 - High priority queue
- 1 - Medium priority queue
- 2 - Normal priority queue
- 3 - Low priority queue
Sending a LEX_RCMD_REQUEST packet with an Option-Length of four (no
priority entries) disables priority queuing. When disabled, the LAN
extension interface unit transfers all packets at a normal (2)
priority level. When a new priority is specified, it overwrites the
previous setting.
5.2 Response Packets - Set Priority
The following packets are valid responses to the Set Priority
LEX_RCMD_REQUEST packet.
* LEX_RCMD_ACK - Set Priority
See the "Conditions for Sending PPP-LEX Packets" section earlier in
this document for more information on this packet type.
* LEX_RCMD_NAK - Set Priority
The LAN extension interface unit sends a LEX_RCMD_NAK packet in
response to the Set Priority LEX_RCMD_REQUEST packet when the request
contains an incorrect number of bytes in the message, when necessary
resources are not available, or when the specified priority is
invalid.
* LEX_RCMD-REJ - Set Priority
See the "Conditions for Sending PPP-LEX Packets" section earlier in
this document for more information on this packet type. Table 7
summarizes the field values of Set Priority LEX_RCMD_ACK,
LEX_RCMD_NAK, and LEX_RCMD_REJ packets.
Table 7 Field Values for Response Packets - Set Priority
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code Valid values:
* 0x41 (LEX_RCMD_ACK packet)
* 0x42 (LEX_RCMD_NAK packet)
* 0x43 (LEX_RCMD_REJ packet)
Identifier A randomly generated value that aids in
matching requests with replies
Length Minimum length = 12 octets
Maximum length = 1028 octets
Option-Type 0x03 (Set Priority)
Option-Flags None
Option-Length Minimum length = 4 octets
Maximum length = 1020 octets
Option-Data Protocol Type and Priority Value sent
in the LEX_RCMD_REQUEST packet
6.0 Disable LAN Extension Ethernet Interface
The host router sends a LEX_RCMD_ REQUEST with an Option-Type of 0x04
to the LAN extension interface unit to disable the LAN extension
Ethernet interface. This remote command option stops data traffic
from the LAN extension interface unit to the host router for
troubleshooting or for reconfiguring the LAN extension interface
unit. This remote command option only affects data traffic. PPP-LEX
control packets can still be transferred over the serial link.
6.1 LEX RCMD_REQUEST - Disable LAN Extension Ethernet Interface
Figure 9 shows a frame format summary of a LEX_RCMD_REQUEST packet
for the Disable LAN Extension Ethernet Interface remote command
option. The host router transmits the fields from left to right.
Figure 9 LEX_RCMD_REQUEST Packet Frame Format -
Disable LAN Extension Ethernet Interface
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF03 Protocol-Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2 octets) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
LAN Extension Interface Remote Command Options
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags Option-Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
Summary Field Descriptions
For complete descriptions of the fields in the PPP Header, the LAN
Extension Interface Protocol Header, and the LAN Extension Interface
Remote Command Option, refer to the "Remote Command Options" section
earlier in this document. The following table provides a summary of
these fields when sending a LEX_RCMD_REQUEST packet that disables the
LAN extension interface unit.
Table 8 Field Values for LEX_RCMD_REQUEST Packet -
Disable LAN Extension Ethernet Interface
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code 0x40 (LEX_RCMD_REQUEST packet)
Identifier Valid values: 0x01-0xFF
Length 12 octets
Option-Type 0x04 (Disable LAN Extension Ethernet
Interface)
Option-Flags None
Option-Length 4 octets
Option-Data None
6.2 Response Packets - Disable LAN Extension Ethernet Interface
LEX_RCMD_ACK, LEX_RCMD_NAK, and LEX_RCMD-REJ packets are valid
responses to the Disable LAN Extension Ethernet Interface
LEX_RCMD_REQUEST packet. Refer to the "Conditions for Sending PPP-LEX
Packets" section earlier in this document for more information on
when the LAN extension interface unit sends each of these response
packets. Note that the LAN extension interface unit sends the
LEX_RCMD_ACK packet after shutting down the interface.
Table 9 summarizes the field values of Disable LAN Extension Ethernet
Interface LEX_RCMD_ACK, LEX_RCMD_NAK, and LEX_RCMD_REJ packets.
Table 9 Field Values for Response Packets -
Disable LAN Extension Ethernet Interface
Field Value
Address/Control 0xFF03 (Broadcast address/Unnumbered
information)
Protocol-Type 0x8041 (Control packet)
Code Valid values:
* 0x41 (LEX_RCMD_ACK packet)
* 0x42 (LEX_RCMD_NAK packet)
* 0x43 (LEX_RCMD_REJ packet)
Identifier The same value as that sent by the
LEX_RCMD_REQUEST packet
Length 12 octets
Option-Type 0x04 (Disable LAN Extension Ethernet
Interface)
Option-Flags None
Option-Length 4 octets
Option-Data None
7.0 Enable LAN Extension Ethernet Interface
The host router sends a LEX_RCMD_ REQUEST with an Option-Type of 0x05
to the LAN extension interface unit to enable the LAN extension
Ethernet interface. This remote command option allows LAN traffic to
flow into the LAN extension interface unit after the interface has
been disabled.
7.1 LEX RCMD_REQUEST - Enable LAN Extension Ethernet Interface
Figure 10 shows a frame format summary of a LEX_RCMD_REQUEST packet
for an Enable LAN Extension Ethernet Interface remote command option.
The host router transmits the fields from left to right.
Figure 10 LEX_RCMD_REQUEST Packet Frame Format - Enable LAN Extension
Ethernet Interface
PPP Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
0xFF03 Protocol-Type
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(2 octets) (2)
LAN Extension Interface Protocol Header
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code Identifier Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
LAN Extension Interface Remote Command Options
<-------------------------------------------------------------->
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option-Type Option-Flags Option-Length
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
(1) (1) (2)
Summary Field Descriptions
For complete descriptions of the fields in the PPP Header, the LAN
Extension Interface Protocol Header, and the LAN Extension Interface
Remote Command Option, refer to the "Remote Command Options" section
earlier in this document. Table 10 provides a summary of these fields
when sending a LEX_RCMD_REQUEST packet that enables the LAN extension
Ethernet interface.
Table 10 Field Values for LEX_RCMD_REQUEST Packet -
Enable LAN Extension Ethernet Interface
Field Value
Address/Control 0xFF03 (Broadcas