米葫芦网

RFC2415 - Simulation Studies of Increased Initial TCP Window Size

热度:12℃ 发布时间:2024-11-18 08:48:59

Network Working Group K. Poduri
Request for Comments: 2415 K. Nichols
Category: Informational Bay Networks
September 1998
Simulation Studies of Increased Initial TCP Window Size
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
Abstract
An increase in the permissible initial window size of a TCP
connection, from one segment to three or four segments, has been
under discussion in the tcp-impl working group. This document covers
some simulation studies of the effects of increasing the initial
window size of TCP. Both long-lived TCP connections (file transfers)
and short-lived web-browsing style connections were modeled. The
simulations were performed using the publicly available ns-2
simulator and our custom models and files are also available.
1. IntrodUCtion
We present results from a set of simulations with increased TCP
initial window (IW). The main objectives were to eXPlore the
conditions under which the larger IW was a "win" and to determine the
effects, if any, the larger IW might have on other traffic flows
using an IW of one segment.
This study was inspired by discussions at the Munich IETF tcp-impl
and tcp-sat meetings. A proposal to increase the IW size to about 4K
bytes (4380 bytes in the case of 1460 byte segments) was discussed.
Concerns about both the utility of the increase and its effect on
other traffic were raised. Some studies were presented showing the
positive effects of increased IW on individual connections, but no
studies were shown with a wide variety of simultaneous traffic flows.
It appeared that some of the questions being raised could be
addressed in an ns-2 simulation. Early results from our simulations
were previously posted to the tcp-impl mailing list and presented at
the tcp-impl WG meeting at the December 1997 IETF.
2. Model and Assumptions
We simulated a network topology with a bottleneck link as shown:
10Mb, 10Mb,
(all 4 links) (all 4 links)
C n2_________ ______ n6 S
l n3_________ /______ n7 e
i 1.5Mb, 50ms // r
e n0 ------------------------ n1 v
n n4__________// _____ n8 e
t n5__________/ ______ n9 r
s s
URLs --> <--- FTP & Web data
File downloading and web-browsing clients are attached to the nodes
(n2-n5) on the left-hand side. These clients are served by the FTP
and Web servers attached to the nodes (n6-n9) on the right-hand side.
The links to and from those nodes are at 10 Mbps. The bottleneck link
is between n1 and n0. All links are bi-directional, but only ACKs,
SYNs, FINs, and URLs are flowing from left to right. Some simulations
were also performed with data traffic flowing from right to left
simultaneously, but it had no effect on the results.
In the simulations we assumed that all ftps transferred 1-MB files
and that all web pages had exactly three embedded URLs. The web
clients are browsing quite aggressively, requesting a new page after
a random delay uniformly distributed between 1 and 5 seconds. This is
not meant to realistically model a single user"s web-browsing
pattern, but to create a reasonably heavy traffic load whose
individual tcp connections accurately reflect real web traffic. Some
discussion of these models as used in earlier studies is available in
references [3] and [4].
The maximum tcp window was set to 11 packets, maximum packet (or
segment) size to 1460 bytes, and buffer sizes were set at 25 packets.
(The ns-2 TCPs require setting window sizes and buffer sizes in
number of packets. In our tcp-full code some of the internal
parameters have been set to be byte-oriented, but external values
must still be set in number of packets.) In our simulations, we
varied the number of data segments sent into a new TCP connection (or
initial window) from one to four, keeping all segments at 1460 bytes.
A dropped packet causes a restart window of one segment to be used,
just as in current practice.
For ns-2 users: The tcp-full code was modified to use an
"application" class and three application client-server pairs were
written: a simple file transfer (ftp), a model of http1.0 style web
connection and a very rough model of http1.1 style web connection.
The required files and scripts for these simulations are available
under the contributed code section on the ns-simulator web page at
the sites ftp://ftp.ee.lbl.gov/IW.{tar, tar.Z} or http://www-
nrg.ee.lbl.gov/floyd/tcp_init_win.Html.
Simulations were run with 8, 16, 32 web clients and a number of ftp
clients ranging from 0 to 3. The IW was varied from 1 to 4, though
the 4-packet case lies beyond what is currently recommended. The
figures of merit used were goodput, the median page delay seen by the
web clients and the median file transfer delay seen by the ftp
clients. The simulated run time was rather large, 360 seconds, to
ensure an adequate sample. (Median values remained the same for
simulations with larger run times and can be considered stable)
3. Results
In our simulations, we varied the number of file transfer clients in
order to change the congestion of the link. Recall that our ftp
clients continuously request 1 Mbyte transfers, so the link
utilization is over 90% when even a single ftp client is present.
When three file transfer clients are running simultaneously, the
resultant congestion is somewhat pathological, making the values
recorded stable. Though all connections use the same initial window,
the effect of increasing the IW on a 1 Mbyte file transfer is not
detectable, thus we focus on the web browsing connections. (In the
tables, we use "webs" to indicate number of web clients and "ftps" to
indicate the number of file transfer clients attached.) Table 1 shows
the median delays experienced by the web transfers with an increase
in the TCP IW. There is clearly an improvement in transfer delays
for the web connections with increase in the IW, in many cases on the
order of 30%. The steepness of the performance improvement going
from an IW of 1 to an IW of 2 is mainly due to the distribution of
files fetched by each URL (see references [1] and [2]); the median
size of both primary and in-line URLs fits completely into two
packets. If file distributions change, the shape of this curve may
also change.
Table 1. Median web page delay
#Webs #FTPs IW=1 IW=2 IW=3 IW=4
(s) (% decrease)
----------------------------------------------
8 0 0.56 14.3 17.9 16.1
8 1 1.06 18.9 25.5 32.1
8 2 1.18 16.1 17.1 28.9
8 3 1.26 11.9 19.0 27.0
16 0 0.64 11.0 15.6 18.8
16 1 1.04 17.3 24.0 35.6
16 2 1.22 17.2 20.5 25.4
16 3 1.31 10.7 21.4 22.1
32 0 0.92 17.6 28.6 21.0
32 1 1.19 19.6 25.0 26.1
32 2 1.43 23.8 35.0 33.6
32 3 1.56 19.2 29.5 33.3
Table 2 shows the bottleneck link utilization and packet drop
percentage of the same experiment. Packet drop rates did increase
with IW, but in all cases except that of the single most pathological
overload, the increase in drop percentage was less than 1%. A
decrease in packet drop percentage is observed in some overloaded
situations, specifically when ftp transfers consumed most of the link
bandwidth and a large number of web transfers shared the remaining
bandwidth of the link. In this case, the web transfers experience
severe packet loss and some of the IW=4 web clients suffer multiple
packet losses from the same window, resulting in longer recovery
times than when there is a single packet loss in a window. During the
recovery time, the connections are inactive which alleviates
congestion and thus results in a decrease in the packet drop
percentage. It should be noted that such observations were made only
in extremely overloaded scenarios.
Table 2. Link utilization and packet drop rates
Percentage Link Utilization Packet drop rate
#Webs #FTPs IW=1 IW=2 IW=3 IW=4 IW=1 IW=2 IW=3 IW=4
-----------------------------------------------------------------------
8 0 34 37 38 39 0.0 0.0 0.0 0.0
8 1 95 92 93 92 0.6 1.2 1.4 1.3
8 2 98 97 97 96 1.8 2.3 2.3 2.7
8 3 98 98 98 98 2.6 3.0 3.5 3.5
-----------------------------------------------------------------------
16 0 67 69 69 67 0.1 0.5 0.8 1.0
16 1 96 95 93 92 2.1 2.6 2.9 2.9
16 2 98 98 97 96 3.5 3.6 4.2 4.5
16 3 99 99 98 98 4.5 4.7 5.2 4.9
-----------------------------------------------------------------------
32 0 92 87 85 84 0.1 0.5 0.8 1.0
32 1 98 97 96 96 2.1 2.6 2.9 2.9
32 2 99 99 98 98 3.5 3.6 4.2 4.5
32 3 100 99 99 98 9.3 8.4 7.7 7.6
To get a more complete picture of performance, we computed the
network power, goodput divided by median delay (in Mbytes/ms), and
plotted it against IW for all scenarios. (Each scenario is uniquely
identified by its number of webs and number of file transfers.) We
plot these values in Figure 1 (in the pdf version), illustrating a
general advantage to increasing IW. When a large number of web
clients is combined with ftps, particularly multiple ftps,
pathological cases result from the extreme congestion. In these
cases, there appears to be no particular trend to the results of
increasing the IW, in fact simulation results are not particularly
stable.
To get a clearer picture of what is happening across all the tested
scenarios, we normalized the network power values for the non-
pathological scenario by the network power for that scenario at IW of
one. These results are plotted in Figure 2. As IW is increased from
one to four, network power increased by at least 15%, even in a
congested scenario dominated by bulk transfer traffic. In simulations
where web traffic has a dominant share of the available bandwidth,
the increase in network power was up to 60%.
The increase in network power at higher initial window sizes is due
to an increase in throughput and a decrease in the delay. Since the
(slightly) increased drop rates were accompanied by better
performance, drop rate is clearly not an indicator of user level
performance.
The gains in performance seen by the web clients need to be balanced
against the performance the file transfers are seeing. We computed
ftp network power and show this in Table 3. It appears that the
improvement in network power seen by the web connections has
negligible effect on the concurrent file transfers. It can be
observed from the table that there is a small variation in the
network power of file transfers with an increase in the size of IW
but no particular trend can be seen. It can be concluded that the
network power of file transfers essentially remained the same.
However, it should be noted that a larger IW does allow web transfers
to gain slightly more bandwidth than with a smaller IW. This could
mean fewer bytes transferred for FTP applications or a slight
decrease in network power as computed by us.
Table 3. Network power of file transfers with an increase in the TCP
IW size
#Webs #FTPs IW=1 IW=2 IW=3 IW=4
--------------------------------------------
8 1 4.7 4.2 4.2 4.2
8 2 3.0 2.8 3.0 2.8
8 3 2.2 2.2 2.2 2.2
16 1 2.3 2.4 2.4 2.5
16 2 1.8 2.0 1.8 1.9
16 3 1.4 1.6 1.5 1.7
32 1 0.7 0.9 1.3 0.9
32 2 0.8 1.0 1.3 1.1
32 3 0.7 1.0 1.2 1.0
The above simulations all used http1.0 style web connections, thus, a
natural question is to ask how results are affected by migration to
http1.1. A rough model of this behavior was simulated by using one
connection to send all of the information from both the primary URL
and the three embedded, or in-line, URLs. Since the transfer size is
now made up of four web files, the steep improvement in performance
between an IW of 1 and an IW of two, noted in the previous results,
has been smoothed. Results are shown in Tables 4 & 5 and Figs. 3 & 4.
Occasionally an increase in IW from 3 to 4 decreases the network
power owing to a non-increase or a slight decrease in the throughput.
TCP connections opening up with a higher window size into a very
congested network might experience some packet drops and consequently
a slight decrease in the throughput. This indicates that increase of
the initial window sizes to further higher values (>4) may not always
result in a favorable network performance. This can be seen clearly
in Figure 4 where the network power shows a decrease for the two
highly congested cases.
Table 4. Median web page delay for http1.1
#Webs #FTPs IW=1 IW=2 IW=3 IW=4
(s) (% decrease)
----------------------------------------------
8 0 0.47 14.9 19.1 21.3
8 1 0.84 17.9 19.0 25.0
8 2 0.99 11.5 17.3 23.0
8 3 1.04 12.1 20.2 28.3
16 0 0.54 07.4 14.8 20.4
16 1 0.89 14.6 21.3 27.0
16 2 1.02 14.7 19.6 25.5
16 3 1.11 09.0 17.0 18.9
32 0 0.94 16.0 29.8 36.2
32 1 1.23 12.2 28.5 21.1
32 2 1.39 06.5 13.7 12.2
32 3 1.46 04.0 11.0 15.0
Table 5. Network power of file transfers with an increase in the
TCP IW size
#Webs #FTPs IW=1 IW=2 IW=3 IW=4
--------------------------------------------
8 1 4.2 4.2 4.2 3.7
8 2 2.7 2.5 2.6 2.3
8 3 2.1 1.9 2.0 2.0
16 1 1.8 1.8 1.5 1.4
16 2 1.5 1.2 1.1 1.5
16 3 1.0 1.0 1.0 1.0
32 1 0.3 0.3 0.5 0.3
32 2 0.4 0.3 0.4 0.4
32 3 0.4 0.3 0.4 0.5
For further insight, we returned to the http1.0 model and mixed some
web-browsing connections with IWs of one with those using IWs of
three. In this experiment, we first simulated a total of 16 web-
browsing connections, all using IW of one. Then the clients were
split into two groups of 8 each, one of which uses IW=1 and the other
used IW=3.
We repeated the simulations for a total of 32 and 64 web-browsing
clients, splitting those into groups of 16 and 32 respectively. Table
6 shows these results. We report the goodput (in Mbytes), the web
page delays (in milli seconds), the percent utilization of the link
and the percent of packets dropped.
Table 6. Results for half-and-half scenario
Median Page Delays and Goodput (MB) Link Utilization (%) & Drops (%)
#Webs IW=1 IW=3 IW=1 IW=3
G.put dly G.put dly L.util Drops L.util Drops
-------------------------------------------------------------------
16 35.5 0.64 36.4 0.54 67 0.1 69 0.7
8/8 16.9 0.67 18.9 0.52 68 0.5
-------------------------------------------------------------------
32 48.9 0.91 44.7 0.68 92 3.5 85 4.3
16/16 22.8 0.94 22.9 0.71 89 4.6
--------------------------------------------------------------------
64 51.9 1.50 47.6 0.86 98 13.0 91 8.6
32/32 29.0 1.40 22.0 1.20 98 12.0
Unsurprisingly, the non-split experiments are consistent with our
earlier results, clients with IW=3 outperform clients with IW=1. The
results of running the 8/8 and 16/16 splits show that running a
mixture of IW=3 and IW=1 has no negative effect on the IW=1
conversations, while IW=3 conversations maintain their performance.
However, the 32/32 split shows that web-browsing connections with
IW=3 are adversely affected. We believe this is due to the
pathological dynamics of this extremely congested scenario. Since
embedded URLs open their connections simultaneously, very large
number of TCP connections are arriving at the bottleneck link
resulting in multiple packet losses for the IW=3 conversations. The
myriad problems of this simultaneous opening strategy is, of course,
part of the motivation for the development of http1.1.
4. Discussion
The indications from these results are that increasing the initial
window size to 3 packets (or 4380 bytes) helps to improve perceived
performance. Many further variations on these simulation scenarios
are possible and we"ve made our simulation models and scripts
available in order to facilitate others" experiments.
We also used the RED queue management included with ns-2 to perform
some other simulation studies. We have not reported on those results
here since we don"t consider the studies complete. We found that by
adding RED to the bottleneck link, we achieved similar performance
gains (with an IW of 1) to those we found with increased IWs without
RED. Others may wish to investigate this further.
Although the simulation sets were run for a T1 link, several
scenarios with varying levels of congestion and varying number of web
and ftp clients were analyzed. It is reasonable to expect that the
results would scale for links with higher bandwidth. However,
interested readers could investigate this ASPect further.
We also used the RED queue management included with ns-2 to perform
some other simulation studies. We have not reported on those results
here since we don"t consider the studies complete. We found that by
adding RED to the bottleneck link, we achieved similar performance
gains (with an IW of 1) to those we found with increased IWs without
RED. Others may wish to investigate this further.
5. References
[1] B. Mah, "An Empirical Model of HTTP Network Traffic", Proceedings
of INFOCOM "97, Kobe, Japan, April 7-11, 1997.
[2] C.R. Cunha, A. Bestavros, M.E. Crovella, "Characteristics of WWW
Client-based Traces", Boston University Computer Science
Technical Report BU-CS-95-010, July 18, 1995.
[3] K.M. Nichols and M. Laubach, "Tiers of Service for Data Access in
a HFC Architecture", Proceedings of SCTE Convergence Conference,
January, 1997.
[4] K.M. Nichols, "Improving Network Simulation with Feedback",
available from knichols@baynetworks.com
6. Acknowledgements
This work benefited from discussions with and comments from Van
Jacobson.
7. Security Considerations
This document discusses a simulation study of the effects of a
proposed change to TCP. Consequently, there are no security
considerations directly related to the document. There are also no
known security considerations associated with the proposed change.
8. Authors" Addresses
Kedarnath Poduri
Bay Networks
4401 Great America Parkway
SC01-04
Santa Clara, CA 95052-8185
Phone: +1-408-495-2463
Fax: +1-408-495-1299
EMail: kpoduri@Baynetworks.com
Kathleen Nichols
Bay Networks
4401 Great America Parkway
SC01-04
Santa Clara, CA 95052-8185
EMail: knichols@baynetworks.com
Full Copyright Statement
Copyright (C) The Internet Society (1998). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

网友评论
评论
发 布

更多软件教程
  • 软件教程推荐
更多+
Greenfoot设置中文的方法

Greenfoot设置中文的方法

Greenfoot是一款简单易用的Java开发环境,该软件界面清爽简约,既可以作为一个开发框使用,也能够作为集成开发环境使用,操作起来十分简单。这款软件支持多种语言,但是默认的语言是英文,因此将该软件下载到电脑上的时候,会发现软件的界面语言是英文版本的,这对于英语基础较差的朋友来说,使用这款软件就会...

07-05

Egret UI Editor修改快捷键的方法

Egret UI Editor修改快捷键的方法

Egret UI Editor是一款开源的2D游戏开发代码编辑软件,其主要功能是针对Egret项目中的Exml皮肤文件进行可视化编辑,功能十分强大。我们在使用这款软件的过程中,可以将一些常用操作设置快捷键,这样就可以简化编程,从而提高代码编辑的工作效率。但是这款软件在日常生活中使用得不多,并且专业性...

07-05

KittenCode新建项目的方法

KittenCode新建项目的方法

KittenCode是一款十分专业的编程软件,该软件给用户提供了可视化的操作界面,支持Python语言的编程开发以及第三方库管理,并且提供了很多实用的工具,功能十分强大。我们在使用这款软件进行编程开发的过程中,最基本、最常做的操作就是新建项目,因此我们很有必要掌握新建项目的方法。但是这款软件的专业性...

07-05

Thonny设置中文的方法

Thonny设置中文的方法

Thonny是一款十分专业的Python编辑软件,该软件界面清爽简单,给用户提供了丰富的编程工具,具备代码补全、语法错误显示等功能,非常的适合新手使用。该软件还支持多种语言,所以在下载这款软件的时候,有时候下载到电脑中的软件是英文版本的,这对于英语基础较差的小伙伴来说,使用这款软件就会变得十分困难,...

07-05

最新软件下载