米葫芦网

RFC2160 - Carrying PostScript in X.400 and MIME

热度:11℃ 发布时间:2024-11-18 09:32:22

Network Working Group H. Alvestrand
Request for Comments: 2160 UNINETT
Category: Standards Track January 1998
Carrying PostScript in X.400 and MIME
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1998). All Rights Reserved.
Table of Contents
1 IntrodUCtion ............................................ 1
2 The PostScript body part ................................ 1
3 The PostScript FTBP ..................................... 2
4 The Application/PostScript content-type ................. 2
5 MIXER conversion ........................................ 2
6 MIXER conversion ........................................ 2
7 OID Assignments ......................................... 3
8 Security Issues ......................................... 3
9 Trademark Issues ........................................ 3
10 References ............................................. 3
11 Author"s Address ....................................... 4
12 Full Copyright Statement ............................... 5
1. Introduction
This document describes methods for carrying PostScript information
in the two standard mail systems MIME and X.400, and the conversion
between them. It uses the notational conventions of [BODYMAP], and
the conversion is further described in [MIXER].
Two ways of carrying PostScript in X.400 are described. One is using
the FTAM Body Part, and one uses the Extended Body Part originally
described in RFC1494.
The FTAM method is recommended.
2. The PostScript body part
Carrying PostScript in X.400 as an Extended Body Part was originally
defined in RFC1494. This specification carries that work forward
now that RFC1494 is obsoleted by [BODYMAP].
The following Extended Body Part is defined for PostScript data
streams. It has no parameters.
postscript-body-part EXTENDED-BODY-PART-TYPE
DATA OCTET STRING
::= mime-postscript-body
mime-postscript-body OBJECT IDENTIFIER ::=
{ mixer-bp-data 2 }
3. The PostScript FTBP
The PostScript FTBP is identified by having the
FileTransferParameters.environment.application-reference set to id-
mime-ftbp-postscript.
The definition is:
id-mime-ftbp-postscript OBJECT IDENTIFIER ::=
{ mixer-bp-data 6 }
4. The Application/PostScript content-type
In MIME, PostScript is carried in the body part
"application/PostScript", which is defined in RFC1521.
5. MIXER conversion
X.400 Body Part: Extended Body Part, OID mime-postscript-body MIME
Content-Type: application/postscript Conversion Type: No conversion
The two representations of PostScript both contain a single stream of
octets. This stream of octets can be copied with no problems between
the representations. No other data needs to be converted.
6. MIXER conversion
X.400 Body Part: FTBP, OID mime-ftbp-postscript-body MIME Content-
Type: application/postscript Conversion Type: No conversion
The two representations of PostScript both contain a single stream of
octets. This stream of octets can be copied with no problems between
the representations. No other data needs to be converted.
7. OID Assignments
The first OID is also defined in [BODYMAP].
POSTSCRIPT-MAPPINGS DEFINITIONS ::= BEGIN
EXPORTS -- everything --;
IMPORTS
mixer-bp-data
FROM MIXER-MAPPINGS
id-mime-postscript-body OBJECT IDENTIFIER ::=
{ mixer-bp-data 2 };
id-mime-ftbp-postscript OBJECT IDENTIFIER ::=
{ mixer-bp-data 6 };
END
8. Security Issues
The issues concerning PostScript and security are well discussed in
RFC2046. No additional security issues are identified by this memo.
9. Trademark Issues
PostScript is a trademark of Adobe Systems, Inc.
10. References
[MIXER]
Kille, S., "MIXER: Mapping between X.400
and RFC822/MIME", RFC2156, January 1998.
[BODYMAP]
Alvestrand, H., "Mapping between X.400 and RFC822/MIME
Message Bodies", RFC2157, January 1998.
11. Author"s Address
Harald Tveit Alvestrand
UNINETT
Postboks 6883 Elgeseter
N-7002 TRONDHEIM
Phone: +47 73 59 70 94
EMail: Harald.T.Alvestrand@uninett.no
12. Full Copyright Statement
Copyright (C) The Internet Society (1998). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

网友评论
评论
发 布

更多软件教程
  • 软件教程推荐
更多+
Greenfoot设置中文的方法

Greenfoot设置中文的方法

Greenfoot是一款简单易用的Java开发环境,该软件界面清爽简约,既可以作为一个开发框使用,也能够作为集成开发环境使用,操作起来十分简单。这款软件支持多种语言,但是默认的语言是英文,因此将该软件下载到电脑上的时候,会发现软件的界面语言是英文版本的,这对于英语基础较差的朋友来说,使用这款软件就会...

07-05

Egret UI Editor修改快捷键的方法

Egret UI Editor修改快捷键的方法

Egret UI Editor是一款开源的2D游戏开发代码编辑软件,其主要功能是针对Egret项目中的Exml皮肤文件进行可视化编辑,功能十分强大。我们在使用这款软件的过程中,可以将一些常用操作设置快捷键,这样就可以简化编程,从而提高代码编辑的工作效率。但是这款软件在日常生活中使用得不多,并且专业性...

07-05

KittenCode新建项目的方法

KittenCode新建项目的方法

KittenCode是一款十分专业的编程软件,该软件给用户提供了可视化的操作界面,支持Python语言的编程开发以及第三方库管理,并且提供了很多实用的工具,功能十分强大。我们在使用这款软件进行编程开发的过程中,最基本、最常做的操作就是新建项目,因此我们很有必要掌握新建项目的方法。但是这款软件的专业性...

07-05

Thonny设置中文的方法

Thonny设置中文的方法

Thonny是一款十分专业的Python编辑软件,该软件界面清爽简单,给用户提供了丰富的编程工具,具备代码补全、语法错误显示等功能,非常的适合新手使用。该软件还支持多种语言,所以在下载这款软件的时候,有时候下载到电脑中的软件是英文版本的,这对于英语基础较差的小伙伴来说,使用这款软件就会变得十分困难,...

07-05

最新软件下载